Yes, it is possible. To set the programmable controller to RUN again, while the programmable controller is stopped, set

Only one GT1020/GT1030 series (5 V type) can be connected to the FX3G series. To connect two GOTs, select the GT1020/GT1

Yes, it is possible. Set a new value for the target address to the target address change value (BFM#54, #53) during the

When a flag contact is not programmed directly under the instruction to be checked, the flag may be turned off depending

The constant operation processing time can be achieved by using constant scan mode. Refer to the programming manual of t

Since they are octal, the number after X7 is X10 and after X77 is X100.

FX3U-16CCL-M CC-Link master block and the FX3U-64CCL CC-Link interface block supports CC-Link Ver.2.0. Both blocks are

The "FX2NC-100MPCB" power supply cable for main unit is provided with the FX3UC-16MR/DS-T. The "FX2NC-100MPCB" and the "

This function allows you to select the digital value to perform D/A conversion from the following three patterns dependi

Since the FX5 CPU modules only support the master function, CC-Link IE Field Network Basic communication between FX5 CPU

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Controllers MELSEC(1637)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(578)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)
Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

701-710 of Total 1055

prev 71 / 106page next

M8037 (forced STOP signal)

Yes, it is possible. To set the programmable controller to RUN again, while the programmable controller is stopped, set the built-in RUN/STOP switch as follo... More Details >>
- No：24965
- Release Date：2019/04/23 07:18
- Category： MELSEC-F Series , Main Unit
Connection of the FX3G series and the GT1020/GT1030 series (5 V type)

Only one GT1020/GT1030 series (5 V type) can be connected to the FX3G series. To connect two GOTs, select the GT1020/GT1030 series (24 V type). More Details >>
- No：24969
- Release Date：2019/04/23 07:19
- Category： MELSEC-F Series , Main Unit
Target address change during the positioning operation in the FX3U-1PG

Yes, it is possible. Set a new value for the target address to the target address change value (BFM#54, #53) during the positioning operation. 　　 * The targ... More Details >>
- No：24986
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Positioning Control
Instruction execution complete flag

When a flag contact is not programmed directly under the instruction to be checked, the flag may be turned off depending on the execution status of another i... More Details >>
- No：24988
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Main Unit
Operation processing time of the programmable controller

The constant operation processing time can be achieved by using constant scan mode. Refer to the programming manual of the programmable controller used. More Details >>
- No：24997
- Release Date：2019/04/23 10:38
- Category： MELSEC-F Series , Engineering Software , Main Unit
Input numbers of the FX programmable controllers

Since they are octal, the number after X7 is X10 and after X77 is X100. More Details >>
- No：25000
- Release Date：2019/04/23 10:39
- Category： MELSEC-F Series , Engineering Software , Main Unit
FX series products that support CC-Link Ver.2.0

FX3U-16CCL-M CC-Link master block and the FX3U-64CCL CC-Link interface block supports CC-Link Ver.2.0. Both blocks are dedicated for the FX3 series. More Details >>
- No：25004
- Release Date：2019/04/23 11:11
- Category： MELSEC-F Series , Network/Communication
Accessories of the FX3UC-16MR/DS-T and the FX3UC-16MR/D-T

The "FX2NC-100MPCB" power supply cable for main unit is provided with the FX3UC-16MR/DS-T. The "FX2NC-100MPCB" and the "FX2NC-100BPCB" power supply cable for... More Details >>
- No：25005
- Release Date：2019/04/23 11:11
- Category： MELSEC-F Series , Main Unit , Accessories
Regarding the HOLD/CLEAR function of the built-in analog output

This function allows you to select the digital value to perform D/A conversion from the following three patterns depending on the operating status of the CPU... More Details >>
- No：39289
- Release Date：2023/01/12 16:51
- Category： MELSEC iQ-F Series , CPU Module , Analog
Regarding CC-Link IE Field Network Basic Communication Between FX5 CPU Modules

Since the FX5 CPU modules only support the master function, CC-Link IE Field Network Basic communication between FX5 CPU modules is not possible. More Details >>
- No：39297
- Release Date：2023/02/13 16:38
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication

701-710 of Total 1055

Inquiries

page top