Set as follows in the Transfer Setup window. - Select "USB" for "PC side I/F". - Select "GOT" for "PLC side I/F" and

The parameters and auto refresh settings for the FL-net (OPCN-2) interface module cannot be made using the Network Param

If Latch (1) is set in the device setting of PLC parameter, the contents of file registers are cleared by latch clear op

The automatic communication function and dedicated instructions (MBRW instruction and MBREQ instruction) can be used on

The difference is I/O numbers used for input and output (XY). QH42P uses the same I/O numbers both for input and output.

MX Component Version 3.15R or later supports 64-bit Windows 7.

You can use a Q series 18-point screw terminal block with a MELSEC iQ-R series terminal block type I/O module or analog

GX Works2 and GX Developer are supplied with GX Works3. When installing GX Works3, you can select whether to install GX

To update to firmware version “1.100 ” or higher, you need a product with serial number (S/N) or higher listed below. ・

Device comments can not be output to data logging files.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1702)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(643)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

791-800 of Total 1110

prev 80 / 111page next

Transparent function

Set as follows in the Transfer Setup window. - Select "USB" for "PC side I/F". - Select "GOT" for "PLC side I/F" and select "via GOT (direct coupled) tra... More Details >>
- No：22598
- Release Date：2018/09/03 17:29
- Update：2018/09/20 17:55
- Category： MELSEC-Q Series
Reading and writing bits/words using the FL-net (OPCN-2) interface module

The parameters and auto refresh settings for the FL-net (OPCN-2) interface module cannot be made using the Network Parameter items in GX Developer.Set those ... More Details >>
- No：22597
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Cause of file register reset by latch clear operation in universal model QCPU

If Latch (1) is set in the device setting of PLC parameter, the contents of file registers are cleared by latch clear operation. Set Latch (2) to maintain t... More Details >>
- No：22584
- Release Date：2018/09/03 17:29
- Update：2018/09/20 17:31
- Category： MELSEC-Q Series
Using the automatic communication function and dedicated instructions at the same time in MODBUS (R) interface module (QJ71MB91)

The automatic communication function and dedicated instructions (MBRW instruction and MBREQ instruction) can be used on the same channel. However, when the... More Details >>
- No：22577
- Release Date：2018/09/03 17:29
- Update：2018/09/20 17:06
- Category： MELSEC-Q Series
Difference between QH42P and QX41Y41P

The difference is I/O numbers used for input and output (XY). QH42P uses the same I/O numbers both for input and output. QX41Y41P uses sequential I/O numbers... More Details >>
- No：22539
- Release Date：2018/09/03 17:28
- Category： MELSEC-Q Series
MX Component Version 3's compatibility with 64-bit Windows 7

MX Component Version 3.15R or later supports 64-bit Windows 7. More Details >>
- No：22520
- Release Date：2018/09/03 17:28
- Category： MELSEC-Q Series
Using Q series terminal blocks and connectors with MELSEC iQ-R series modules

You can use a Q series 18-point screw terminal block with a MELSEC iQ-R series terminal block type I/O module or analog module. For a 40-pin connector type ... More Details >>
- No：22474
- Release Date：2018/09/03 17:28
- Update：2018/09/19 14:37
- Category： MELSEC iQ-R Series
Software to be supplied with GX Works3

GX Works2 and GX Developer are supplied with GX Works3. When installing GX Works3, you can select whether to install GX Works2 and GX Developer together. More Details >>
- No：22463
- Release Date：2018/09/03 17:28
- Update：2018/09/18 16:14
- Category： MELSEC iQ-R Series
Regarding updating the FX5U/FX5UC CPU module to firmware version “1.100 ” or later

To update to firmware version “1.100 ” or higher, you need a product with serial number (S/N) or higher listed below. ・FX5UC-32MT/DS-TS and FX5UC-32MT/DSS-T... More Details >>
- No：44623
- Release Date：2024/11/28 16:14
- Category： MELSEC iQ-F Series , CPU Module
Regarding device comment output to Data Logging Files

Device comments can not be output to data logging files. More Details >>
- No：39321
- Release Date：2023/02/14 09:00
- Category： MELSEC iQ-F Series , CPU Module

791-800 of Total 1110

Inquiries

page top