The input signal forms are different. All the programmable controllers for the domestic market other than the FX3G/FX3U

When a flag contact is not programmed directly under the instruction to be checked, the flag may be turned off depending

Replace the battery when the programmable controller is powered off. For example, for the FX3U/FX3UC series, data will

The execution time of the basic opeartion instruction (LD) of the FX5U/FX5UC/FX5UJ CPU module is 34 ns. *For firmware Ve

Connect with a straight cable using a hub. For more details, refer to the following manual. - FL-net (OPCN-2) Interface

GX Configurator-MB does not need to be purchased. Parameters can be set using GX Works2 alone.

You can check the connection to the hub with bit 10 of the special register SD1288. When bit 10 of the SD1288 is on, the

To assure 32-bit data, "Network Range Assignment" of the control station must satisfy the following conditions.(1) The s

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1731)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

911-920 of Total 1123

prev 92 / 113page next

Differences in the specifications between the programmable controllers used in Japan and overseas.

The input signal forms are different. All the programmable controllers for the domestic market other than the FX3G/FX3U series are the sink input. The progra... More Details >>
- No：24913
- Release Date：2019/04/17 11:39
- Category： MELSEC-F Series , Main Unit
Number of FX3U-64CCL interface blocks that can be added to a main unit

One FX3U-64CCL can be added. More Details >>
- No：24962
- Release Date：2019/04/23 07:17
- Category： MELSEC-F Series , Network/Communication
Instruction execution complete flag

When a flag contact is not programmed directly under the instruction to be checked, the flag may be turned off depending on the execution status of another i... More Details >>
- No：24988
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Main Unit
Battery replacement during power-on

Replacethe battery when the programmable controller is powered off. For example, forthe FX3U/FX3UC series, data will be held for about 20 seconds after be... More Details >>
- No：22257
- Release Date：2018/08/30 13:48
- Update：2019/02/19 11:54
- Category： MELSEC-F Series , Main Unit , Accessories
Regarding the processing specification of the basic operation instruction(LD).

The execution time of the basic opeartion instruction (LD) of the FX5U/FX5UC/FX5UJ CPU module is 34 ns. *For firmware Ver.1.100 or above, this specification ... More Details >>
- No：22287
- Release Date：2018/08/30 13:55
- Update：2023/07/03 11:56
- Category： MELSEC iQ-F Series , CPU Module
Cable used for FL-net

Connect with a straight cable using a hub. For more details, refer to the following manual. - FL-net (OPCN-2) Interface Module User's Manual More Details >>
- No：22574
- Release Date：2018/09/03 17:29
- Update：2018/09/20 16:55
- Category： MELSEC-Q Series
GX Configurator-MB for the MODBUS(R) interface module

GX Configurator-MB does not need to be purchased. Parameters can be set using GX Works2 alone. More Details >>
- No：22701
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
Detecting the connection between a built-in Ethernet port QCPU and hub

You can check the connection to the hub with bit 10 of the special register SD1288. When bit 10 of the SD1288 is on, the QCPU is in connection with the hub. More Details >>
- No：22712
- Release Date：2018/09/03 17:29
- Category： MELSEC-Q Series
MX Component Version 4's compatibility with 64-bit Windows 7

Yes. More Details >>
- No：22844
- Release Date：2018/09/03 17:30
- Category： Engineering Software
32-bit data assurance

To assure 32-bit data, "Network Range Assignment" of the control station must satisfy the following conditions.(1) The start device No. of LB is a multiple o... More Details >>
- No：23052
- Release Date：2018/09/03 17:31
- Category： Network related products

911-920 of Total 1123

Inquiries

page top