Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward n

The non-protocol communication can be set by the following two methods: (1) setting parameters using a programming tool,

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data

The built-in Ethernet on the FX5 CPU module does not support CC-Link IE field networks. If you use a CC-Link IE field n

Yes, it is. However, if the error cause is not eliminated, M8004 will turn on again after powering on. * How to chec

Device back up is available without using a battery. However, to back up link register (W) and file register (R) devices

The bits 0 to F of the special register SD1286 (Receive state signal) correspond to the connection numbers 1 to 16. When

CW Workbench is an engineering tool for C Controller modules that provides basic functions from edits to compilation/deb

Major differences are shown below. - AJ65SBTB1-32DT1 <Input specifications> - Input type positive common (sink ty

No, the operation speed is not changed by changing the indirectly specified value.To change the speed during operation,

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Controllers

Programmable Automation Controllers MELSEC(28)

MELSEC MX Controller MX-R Model
MELSEC MX Controller MX-F Model(28)
MELSEC MX Controller Engineering Software
Programmable Controllers MELSEC(1731)

MELSEC iQ-R Series(45)
MELSEC iQ-F Series(672)
MELSEC-Q Series(213)
MELSEC-L Series(105)
MELSEC-F Series(457)
Network related products(110)
Engineering Software(129)

Motion Controllers(414)

MELSEC iQ-R Series(73)
MELSEC iQ-F Series(29)
MELSEC-Q Series(247)
MELSEC-L Series(64)
Engneering software(1)

FAQ within [ Controllers ]

941-950 of Total 1123

prev 95 / 113page next

Torque limit

Torque is limited by the lower set value of "[Pr.17] Torque limit setting value" and "[Cd.22] New torque value/forward new torque value".When the current tor... More Details >>
- No：23621
- Release Date：2018/09/14 15:09
- Category： RD77MS , RD77GF , FX5SSC
Communication setting methods when the FX3U-232-BD is used

The non-protocol communication can be set by the following two methods: (1) setting parameters using a programming tool, such as GX Works2, or (2) writing da... More Details >>
- No：24773
- Release Date：2019/02/27 15:24
- Category： MELSEC-F Series , Engineering Software , Network/Communication
Data backup failure

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data may be overwritten by execution of t... More Details >>
- No：24783
- Release Date：2019/02/27 16:16
- Category： MELSEC-F Series , Engineering Software , Main Unit
Regarding CC-Link IE field network support of FX5 CPU module built-in Ethernet

The built-in Ethernet on the FX5 CPU module does not support CC-Link IE field networks. If you use a CC-Link IE field network, add an FX5-CCLIEF. *The FX5-... More Details >>
- No：44877
- Release Date：2025/03/18 10:30
- Category： MELSEC iQ-F Series , CPU Module , Network/Communication
How to reset M8004 (Error occurrence)

Yes, it is. However, if the error cause is not eliminated, M8004 will turn on again after powering on. * How to check the error In the FX3S/FX3G/FX3GC/FX... More Details >>
- No：22280
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Engineering Software , Main Unit
Regarding the necessity of using a battery

Device back up is available without using a battery. However, to back up link register (W) and file register (R) devices, a FX3U-32BL (battery) is required. More Details >>
- No：22296
- Release Date：2018/08/30 13:55
- Update：2025/11/07 15:52
- Category： MELSEC iQ-F Series , Option , CPU Module
SD1286 of LCPU with built-in Ethernet port

The bits 0 to F of the special register SD1286 (Receive state signal) correspond to the connection numbers 1 to 16. When it receives data, the corresponding ... More Details >>
- No：22786
- Release Date：2018/09/03 17:30
- Category： MELSEC-L Series
CW Workbench

CW Workbench is an engineering tool for C Controller modules that provides basic functions from edits to compilation/debugging.Using CW Workbench, applicatio... More Details >>
- No：22854
- Release Date：2018/09/03 17:30
- Category： Engineering Software
Difference between AJ65SBTB1-32DTE1 and AJ65SBTB1-32DT1

Major differences are shown below. - AJ65SBTB1-32DT1 - Input type positive common (sink type) - Rated input current approx. 5 mA - ON voltage/ON curr... More Details >>
- No：23022
- Release Date：2018/09/03 17:31
- Update：2018/09/26 09:52
- Category： Network related products
Speed change

No, the operation speed is not changed by changing the indirectly specified value.To change the speed during operation, use CHGV instruction. More Details >>
- No：23555
- Release Date：2018/09/14 15:09
- Category： RnMTCPU , Q17nDSCPU , Q17nDCPU , Q170MSCPU , Q170MCPU , Q17nHCPU , Q17nCPUN

941-950 of Total 1123

Inquiries

page top