Since they are octal, the number after Y7 is Y10 and after Y77 is Y100.

FX3GC series does not support the index modifier for the bit devices. FX3U/FX3UC series supports it.

The FX3U-ENET-L does not support the DHCP function. Set the fixed IP address using FX Configurator-EN-L. (FX Configurato

It is not possible to extend the length of the extension cable to over 65cm. Place the main unit separately by using the

To use the special blocks away from the main unit, connect them with the FX0N-30EC/FX0N-65EC extension cable and the FX2

If the OUT instruction using a latched (battery backed) type auxiliary relay number exists in a sequence program, the in

Up to 2 connections can be opened.

Clear the required area with the ZRST instruction by using the initial pulse when the programmable controller is set to

When the count condition of the counter in the MC circuit remains set, the counter counts when the MC circuit is turned

Whether the positioning parameter is used or the extension positioning parameter is used can be selected in BFM#32 (posi

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-F Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-F Series

Accessories(33)

FAQ within [ MELSEC-F Series ]

1-10 of Total 198

prev 1 / 20page next

Output numbers of the FX programmable controllers

Since they are octal, the number after Y7 is Y10 and after Y77 is Y100. More Details >>
- No：24946
- Release Date：2019/04/18 14:26
- Category： MELSEC-F Series
Index modifier of the bit device in the FX3GC series

FX3GC series does not support the index modifier for the bit devices. FX3U/FX3UC series supports it. More Details >>
- No：25002
- Release Date：2019/04/23 10:39
- Category： MELSEC-F Series
Support of the DHCP (Dynamic Host Configuration Protocol) function by the FX3U-ENET-L (for Ethernet communications)

The FX3U-ENET-L does not support the DHCP function. Set the fixed IP address using FX Configurator-EN-L. (FX Configurator-EN-L can be downloaded from Mitsubi... More Details >>
- No：24869
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series
Extending the extension cable

It is not possible to extend the length of the extension cable to over 65cm. Place the main unit separately by using the parallel link or N:N Network functio... More Details >>
- No：24941
- Release Date：2019/04/18 14:25
- Category： MELSEC-F Series , Accessories
Using special blocks (extension blocks) away from a main unit

To use the special blocks away from the main unit, connect them with the FX0N-30EC/FX0N-65EC extension cable and the FX2N-CNV-BC connector conversion adapter. More Details >>
- No：24966
- Release Date：2019/04/23 07:18
- Category： MELSEC-F Series , Accessories
Use of latched (battery backed) type auxiliary relay

If the OUT instruction using a latched (battery backed) type auxiliary relay number exists in a sequence program, the information held may be overwritten by ... More Details >>
- No：24877
- Release Date：2019/04/15 08:07
- Category： MELSEC-F Series , Main Unit
MELSOFT connection of the FX3U-ENET-L Ethernet interface block

Up to 2 connections can be opened. More Details >>
- No：24919
- Release Date：2019/04/17 11:40
- Category： MELSEC-F Series , Network/Communication
Using a fixed latched (battery backed) type device as a general type device

Clear the required area with the ZRST instruction by using the initial pulse when the programmable controller is set to RUN. To clear all the latched type de... More Details >>
- No：24925
- Release Date：2019/04/17 11:42
- Category： MELSEC-F Series , Main Unit
Measurement of the counter in the MC (master control) circuit

When the count condition of the counter in the MC circuit remains set, the counter counts when the MC circuit is turned on. More Details >>
- No：24910
- Release Date：2019/04/15 11:32
- Category： MELSEC-F Series , Main Unit
Parameter setting of FX3U-1PG

Whether the positioning parameter is used or the extension positioning parameter is used can be selected in BFM#32 (positioning parameter selection). Select ... More Details >>
- No：24917
- Release Date：2019/04/17 11:40
- Category： MELSEC-F Series , Positioning Control

1-10 of Total 198

Inquiries

page top