The FX3U-ENET-ADP does not support the DHCP function. Set the fixed IP address using the parameter setting of GX Works2.

When a coil of the high-speed counter or an interrupt pointer is programmed, the programmable controller system adjusts

Usually, unit number of the first special function unit/block is "K0". However, when the main unit is FX3UC-32MT-LT(-LT2

Since the JOG speed is the positioning parameter, turn off and on the positioning parameter enable command (X-axis: BFM#

When the programmable controller is powered on after a memory cassette is installed, the memory cassette is automaticall

Only one GT1020/GT1030 series (5 V type) can be connected to the FX3G series. To connect two GOTs, select the GT1020/GT1

Yes, it is possible. To set the programmable controller to RUN again, while the programmable controller is stopped, set

An FX3G-CNV-ADP is required. * When the FX3U-ENET-ADP is used with other special adapters, connect the FX3U-ENET-ADP a

One FX3U-ENET-ADP can be connected at the last stage (left end) of adapters for the FX3UC series. *The FX3U-ENET-ADP is

Ver2.00 or later is applicable. (GX Works2 with Ver. 1.87R or later is applicable.) The version of main units can be che

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-F Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-F Series

Accessories(33)

FAQ within [ MELSEC-F Series ]

131-140 of Total 198

prev 14 / 20page next

Support of the DHCP (Dynamic Host Configuration Protocol) function by the FX3U-ENET-ADP (for Ethernet communications)

The FX3U-ENET-ADP does not support the DHCP function. Set the fixed IP address using the parameter setting of GX Works2. On GX Works2, select "Parameter" and... More Details >>
- No：24870
- Release Date：2019/04/15 08:05
- Category： MELSEC-F Series , Network/Communication
Input filter adjustment when a high-speed counter or the interrupt function is used

When a coil of the high-speed counter or an interrupt pointer is programmed, the programmable controller system adjusts the filter constant of the correspond... More Details >>
- No：24867
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , High-Speed Counter
Operation of the first special function unit/block in the FX3UC series

Usually, unit number of the first special function unit/block is "K0". However, when the main unit is FX3UC-32MT-LT(-LT2), the unit number "K0" is assigned t... More Details >>
- No：24995
- Release Date：2019/04/23 10:40
- Category： MELSEC-F Series , Main Unit
Changing the JOG speed in the FX3U-20SSC-H

Since the JOG speed is the positioning parameter, turn off and on the positioning parameter enable command (X-axis: BFM#519.b4, Y-axis: BFM#619.b4) to enable... More Details >>
- No：24987
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Positioning Control
Setting for installing a memory cassette

When the programmable controller is powered on after a memory cassette is installed, the memory cassette is automatically recognized. After the memory casset... More Details >>
- No：24974
- Release Date：2019/04/23 07:20
- Category： MELSEC-F Series , Main Unit
Connection of the FX3G series and the GT1020/GT1030 series (5 V type)

Only one GT1020/GT1030 series (5 V type) can be connected to the FX3G series. To connect two GOTs, select the GT1020/GT1030 series (24 V type). More Details >>
- No：24969
- Release Date：2019/04/23 07:19
- Category： MELSEC-F Series , Main Unit
M8037 (forced STOP signal)

Yes, it is possible. To set the programmable controller to RUN again, while the programmable controller is stopped, set the built-in RUN/STOP switch as follo... More Details >>
- No：24965
- Release Date：2019/04/23 07:18
- Category： MELSEC-F Series , Main Unit
Connection of the FX3G series and the FX3U-ENET-ADP

AnFX3G-CNV-ADP is required. 　 * When the FX3U-ENET-ADP is used with other special adapters, connect the FX3U-ENET-ADP at the last stage (left end). More Details >>
- No：24951
- Release Date：2019/04/18 14:27
- Category： MELSEC-F Series , Main Unit
Number of FX3U-ENET-ADP Ethernet communication special adapters that can be connected to the FX3UC series

One FX3U-ENET-ADP can be connected at the last stage (left end) of adapters for the FX3UC series. *The FX3U-ENET-ADP is a communication special adapter and ... More Details >>
- No：24932
- Release Date：2019/04/23 07:21
- Category： MELSEC-F Series , Main Unit
Supported versions of the FX3G/FX3GC series main units for the CC-Link parameter settings of GX Works2

Ver2.00 or later is applicable. (GX Works2 with Ver. 1.87R or later is applicable.) The version of main units can be checked with the last three digits of t... More Details >>
- No：24922
- Release Date：2019/04/17 11:41
- Category： MELSEC-F Series , Main Unit

131-140 of Total 198

Inquiries

page top