When the count condition of the counter in the MC circuit remains set, the counter counts when the MC circuit is turned

The FX3U-20SSC-H (differential line driver), FX2N-10PG (differential line driver or open collector: only 5 V type), and

If the OUT instruction using a latched (battery backed) type auxiliary relay number exists in a sequence program, the in

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data

Scan time displayed on GX Works2 is the maximum scan time of the monitor target programmable controller CPU. To check c

For the sink input, the "S/S" terminal and the "24V" terminal are needed to be short-circuited.

Power off and on the programmable controller again after the communication setting is changed.

Since the JOG speed is the positioning parameter, turn off and on the positioning parameter enable command (X-axis: BFM#

One extension cable can be used per system. Two or more extension cables cannot be used.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-F Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-F Series

Accessories(33)

FAQ within [ MELSEC-F Series ]

181-190 of Total 198

prev 19 / 20page next

Measurement of the counter in the MC (master control) circuit

When the count condition of the counter in the MC circuit remains set, the counter counts when the MC circuit is turned on. More Details >>
- No：24910
- Release Date：2019/04/15 11:32
- Category： MELSEC-F Series , Main Unit
Positioning blocks/module that can be connected with a manual pulse generator

The FX3U-20SSC-H (differential line driver), FX2N-10PG (differential line driver or open collector: only 5 V type), and FX2N-10GM/FX2N-20GM (open collector) ... More Details >>
- No：24886
- Release Date：2019/04/15 08:07
- Category： MELSEC-F Series , Positioning Control
Use of latched (battery backed) type auxiliary relay

If the OUT instruction using a latched (battery backed) type auxiliary relay number exists in a sequence program, the information held may be overwritten by ... More Details >>
- No：24877
- Release Date：2019/04/15 08:07
- Category： MELSEC-F Series , Main Unit
Data backup failure

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data may be overwritten by execution of t... More Details >>
- No：24783
- Release Date：2019/02/27 16:16
- Category： MELSEC-F Series , Engineering Software , Main Unit
Scan time while operation of a programmable controller CPU is being monitored using GX Works2

Scan time displayed on GX Works2 is the maximum scan time of the monitor target programmable controller CPU. To check current scan time, monitor the data in... More Details >>
- No：24779
- Release Date：2019/02/27 15:58
- Category： MELSEC-F Series , Engineering Software , Main Unit
Input wiring (FX3 series)

For the sink input, the "S/S" terminal and the "24V" terminal are needed to be short-circuited. More Details >>
- No：22272
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit , I/O Extension
Reflecting the changes in the communication setting

Power off and on the programmable controller again after the communication setting is changed. More Details >>
- No：25006
- Release Date：2019/04/23 11:11
- Category： MELSEC-F Series , Engineering Software , Main Unit
Changing the JOG speed in the FX3U-20SSC-H

Since the JOG speed is the positioning parameter, turn off and on the positioning parameter enable command (X-axis: BFM#519.b4, Y-axis: BFM#619.b4) to enable... More Details >>
- No：24987
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Positioning Control
Output frequency of the FX3U-1PG pulse output block

It is from 1 Hz to 200 kHz. More Details >>
- No：24981
- Release Date：2019/04/23 07:21
- Category： MELSEC-F Series , Positioning Control
Number of extension cables that can be used per system

One extension cable can be used per system. Two or more extension cables cannot be used. More Details >>
- No：24958
- Release Date：2019/04/18 14:33
- Category： MELSEC-F Series

181-190 of Total 198

Inquiries

page top