In the FX3U/FX3UC series, a bit in a word device can be specified. It can be specified by "Word device (D only) + Decim

To perform battery-less operation in the FX3U/FX3UC series, set parameters using GX Works2(or GX Developer). Please r

Turn off the drive contact of the WR3A instruction.

Connect the "0V (-)" terminal of the external 24V DC power supply to the "COM" terminal (- side of the built-in power su

The keeping (latched device data) range is fixed and cannot be changed in parameters. (Reference) [When an optional

The comment may not have been written to the programmable controller. Or, the comment display setting may be required o

When you connect the built-in USB port of the FX3 series to the personal computer for the first time, you need to instal

Yes, it is. However, if the error cause is not eliminated, M8004 will turn on again after powering on. * How to chec

To check the version of the MELSEC-F series, connect GX Works2 (personal computer) or HPP to a programmable controller,

The keyword protection cannot be forcibly reset. Since only the keyword that has been registered by the user is accepta

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-F Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-F Series

Accessories(33)

FAQ within [ MELSEC-F Series ]

181-190 of Total 198

prev 19 / 20page next

Using a specified bit (on/off) of a word device (D) as a condition for a contact

In the FX3U/FX3UC series, a bit in a word device can be specified. It can be specified by "Word device (D only) + Decimal point + Bit position (0 to F)". A... More Details >>
- No：22261
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Engineering Software , Main Unit
How to set battery-less operation(FX3U/FX3UC)

To perform battery-less operation in the FX3U/FX3UC series, set parameters using GX Works2(or GX Developer). Please refer to the following manual for furt... More Details >>
- No：22277
- Release Date：2018/08/30 13:48
- Update：2019/02/19 08:47
- Category： MELSEC-F Series , Engineering Software , Main Unit , Accessories
How to stop D/A conversion while the WR3A (Write to Dedicated Analog Block) instruction is being executed in the FX2N-2DA (analog output)

Turn off the drive contact of the WR3A instruction. More Details >>
- No：24872
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , Analog Control
How to wire the 24V DC power supply for sensors

Connect the "0V (-)" terminal of the external 24V DC power supply to the "COM" terminal (- side of the built-in power supply), one of the input terminals of ... More Details >>
- No：22281
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit
How to change the keeping (latched device data) range (FX3G/FX3GC)

The keeping (latched device data) range is fixed and cannot be changed in parameters. (Reference) [When an optional battery is not used] The keeping ran... More Details >>
- No：22260
- Release Date：2018/08/30 13:48
- Update：2019/02/19 11:52
- Category： MELSEC-F Series , Engineering Software , Main Unit , Accessories
Comment display

Thecomment may not have been written tothe programmable controller. Or, the comment display setting may be required on the GX Works2 side. [Writing a com... More Details >>
- No：24681
- Release Date：2019/02/22 11:40
- Update：2019/02/22 14:15
- Category： MELSEC-F Series , Engineering Software , Main Unit
Communications using the built-in USB port of the FX3 series

When you connect the built-in USB port of the FX3 series to the personal computer for the first time, you need to install the USB driver into the personal co... More Details >>
- No：22273
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Engineering Software , Main Unit , Network/Communication
How to reset M8004 (Error occurrence)

Yes, it is. However, if the error cause is not eliminated, M8004 will turn on again after powering on. * How to check the error In the FX3S/FX3G/FX3GC/FX... More Details >>
- No：22280
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Engineering Software , Main Unit
How to check the version of the MELSEC-F series

To check the version of the MELSEC-F series, connect GX Works2 (personal computer) or HPP to a programmable controller, and monitor the data in D8001. The l... More Details >>
- No：24772
- Release Date：2019/02/27 15:22
- Category： MELSEC-F Series , Engineering Software , Main Unit
Keyword protection of the MELSEC-F series

The keyword protection cannot be forcibly reset. Since only the keyword that has been registered by theuser is acceptable, please take measures to ensure th... More Details >>
- No：24784
- Release Date：2019/02/27 16:27
- Category： MELSEC-F Series , Engineering Software , Main Unit

181-190 of Total 198

Inquiries

page top