The frame type supported by MC protocol is equivalent to A-compatible 1E frame.

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data

Each special function unit/block has 8 occupied points, except for some special function devices. These 8 points do no

One FX3U-ENET-ADP can be connected at the last stage (left end) of adapters for the FX3UC series. *The FX3U-ENET-ADP is

The totem pole output encoder cannot be connected to the FX2NC-1HC/ FX2N-1HC/ FX3U-2HC. The connectable encoders are as

FX3U series expansion boards can be added to FX3UC-32MT-LT and FX3UC-32MT-LT2.

Ver2.00 or later is applicable. (GX Works2 with Ver. 1.87R or later is applicable.) The version of main units can be ch

Check whether the lamp is back to normal after disconnecting the wiring of the "24V" (service power supply) terminal. I

Connect the "0V (-)" terminal of the external 24V DC power supply to the "COM" terminal (- side of the built-in power su

The station number setting is not required for non-protocol communication.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-F Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-F Series

Accessories(33)

FAQ within [ MELSEC-F Series ]

71-80 of Total 198

prev 8 / 20page next

MC protocol supported by the FX3U-ENET-L

The frame typesupported byMC protocol is equivalent to A-compatible 1E frame. More Details >>
- No：24702
- Release Date：2019/02/27 08:59
- Category： MELSEC-F Series , Network/Communication
Data backup failure

If the OUT instruction using the device number of the latch target device exists in a sequence program, the latched data may be overwritten by execution of t... More Details >>
- No：24783
- Release Date：2019/02/27 16:16
- Category： MELSEC-F Series , Engineering Software , Main Unit
Number of occupied points of special function devices

Each special function unit/block has 8 occupied points, except for some special function devices. These 8 points do not occupy 8 points of the actual I/O n... More Details >>
- No：24873
- Release Date：2019/04/15 08:06
- Category： MELSEC-F Series , Main Unit
Number of FX3U-ENET-ADP Ethernet communication special adapters that can be connected to the FX3UC series

One FX3U-ENET-ADP can be connected at the last stage (left end) of adapters for the FX3UC series. *The FX3U-ENET-ADP is a communication special adapter and ... More Details >>
- No：24932
- Release Date：2019/04/23 07:21
- Category： MELSEC-F Series , Main Unit
Connection of a totem pole output encoder

The totem pole output encoder cannot be connected to the FX2NC-1HC/FX2N-1HC/ FX3U-2HC. The connectable encoders are as follows. ･ Open collector output typ... More Details >>
- No：25010
- Release Date：2019/04/23 11:12
- Category： MELSEC-F Series , High-Speed Counting
Adding FX3U series expansion boards to an FX3UC series main unit

FX3U series expansion boards can be added to FX3UC-32MT-LT and FX3UC-32MT-LT2. More Details >>
- No：24963
- Release Date：2019/04/23 07:18
- Category： MELSEC-F Series , Main Unit
Supported versions of the FX3G/FX3GC series main units for the CC-Link parameter settings of GX Works2

Ver2.00 or later is applicable. (GX Works2 with Ver. 1.87R or later is applicable.) The version of main units can be checked with the last three digits of t... More Details >>
- No：24922
- Release Date：2019/04/17 11:41
- Category： MELSEC-F Series , Main Unit
The power supply lamp of a running programmable controller suddenly turned off or flashes

Check whether the lamp is back to normalafter disconnecting the wiring of the "24V" (service power supply) terminal. Ifthe lamp is back to normal,the servic... More Details >>
- No：22267
- Release Date：2018/08/30 13:48
- Update：2019/02/19 11:53
- Category： MELSEC-F Series , Main Unit
How to wire the 24V DC power supply for sensors

Connect the "0V (-)" terminal of the external 24V DC power supply to the "COM" terminal (- side of the built-in power supply), one of the input terminals of ... More Details >>
- No：22281
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit
Station number setting in the "PLC System(2)" tab of PLC Parameter setting on GX Developer when non-protocol communication is performed

The station number setting is not required for non-protocol communication. More Details >>
- No：24948
- Release Date：2019/04/18 14:27
- Category： MELSEC-F Series , Main Unit , Network/Communication

71-80 of Total 198

Inquiries

page top