The operation is not guaranteed. Please select the extension blocks and units from FX2N series.

FX3U/FX3UC series (Ver. 2.20 or later) * To connect the FX3U-1PG to the FX3UC series, the FX2NC-CNV-IF connector convers

Although it depends on the operating environment, wiring within 20 m is generally recommended.

They can be used together. * 14/24-point type FX3G series main unit ･ An expansion board can be connected to BD1 (1st po

For the sink input, the "S/S" terminal and the "24V" terminal are needed to be short-circuited.

The FX3U-ENET-ADP does not support the DHCP function. Set the fixed IP address using the parameter setting of GX Works2.

It is transistor output. Transistor output specifications are as follows. ･ Rated load voltage 5 to 24 V DC ･ Maximum lo

GX Works2 with Ver. 1.87R or later is required.

When a flag contact is not programmed directly under the instruction to be checked, the flag may be turned off depending

The constant operation processing time can be achieved by using constant scan mode. Refer to the programming manual of t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-F Series

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

MELSEC-F Series

Accessories(33)

FAQ within [ MELSEC-F Series ]

81-90 of Total 198

prev 9 / 20page next

Extension blocks and units that can be used in the FX3U series

The operation is not guaranteed. Please select the extension blocks and units from FX2N series. More Details >>
- No：24935
- Release Date：2019/04/18 14:24
- Category： MELSEC-F Series , Main Unit , I/O Extension
Programmable controller series which the FX3U-1PG pulse output block can be added to

FX3U/FX3UC series (Ver. 2.20 or later) * To connect the FX3U-1PG to the FX3UC series, the FX2NC-CNV-IF connector conversion adapter or the FX3UC-1PS-5V exte... More Details >>
- No：24947
- Release Date：2019/04/18 14:26
- Category： MELSEC-F Series , Positioning Control
Maximum length of input wiring

Although it depends on the operating environment, wiring within 20 m is generally recommended. More Details >>
- No：24949
- Release Date：2019/04/18 14:29
- Category： Main Unit
Connection of expansion boards and a memory cassette to the FX3G series main unit

They can be used together. * 14/24-point type FX3G series main unit ･ An expansion board can be connected to BD1 (1st position) and a memory cassette can b... More Details >>
- No：24952
- Release Date：2019/04/18 14:27
- Category： MELSEC-F Series , Main Unit
Input wiring (FX3 series)

For the sink input, the "S/S" terminal and the "24V" terminal are needed to be short-circuited. More Details >>
- No：22263
- Release Date：2018/08/30 13:48
- Category： MELSEC-F Series , Main Unit , I/O Extension
Support of the DHCP (Dynamic Host Configuration Protocol) function by the FX3U-ENET-ADP (for Ethernet communications)

The FX3U-ENET-ADP does not support the DHCP function. Set the fixed IP address using the parameter setting of GX Works2. On GX Works2, select "Parameter" and... More Details >>
- No：24870
- Release Date：2019/04/15 08:05
- Category： MELSEC-F Series , Network/Communication
Pulse output type of the FX3U-1PG pulse output block

It is transistor output. Transistor output specifications are as follows. ･ Rated load voltage 5 to 24 V DC ･ Maximum load current 20 mA or lower More Details >>
- No：24972
- Release Date：2019/04/23 07:19
- Category： MELSEC-F Series , Positioning Control
Settings for the FX3U-ENET-ADP

GX Works2 with Ver. 1.87R or later is required.　 More Details >>
- No：24781
- Release Date：2019/02/27 16:10
- Category： MELSEC-F Series , Engineering Software , Network/Communication
Instruction execution complete flag

When a flag contact is not programmed directly under the instruction to be checked, the flag may be turned off depending on the execution status of another i... More Details >>
- No：24988
- Release Date：2019/04/23 07:22
- Category： MELSEC-F Series , Main Unit
Operation processing time of the programmable controller

The constant operation processing time can be achieved by using constant scan mode. Refer to the programming manual of the programmable controller used. More Details >>
- No：24997
- Release Date：2019/04/23 10:38
- Category： MELSEC-F Series , Engineering Software , Main Unit

81-90 of Total 198

Inquiries

page top