The comment may not have been written to the programmable controller. Or, the comment display setting may be required o

D200 to D7999 and R0 to R32767 can be latched. D200 to D511 can be set as non-latch areas in parameters. For details o

Yes, it is. However, if the error cause is not eliminated, M8004 will turn on again after powering on. * How to chec

The station number setting is not required for non-protocol communication.

In the FX3U/FX3UC series, a bit in a word device can be specified. It can be specified by "Word device (D only) + Decim

When a personal computer (GX Works2) is connected to the RS-232C port of a programmable controller, communications betwe

The present scan time is stored in D8010. Monitor the value using a programming tool such as GX Works2 and GX Developer.

Numerical value data 0 to 255 corresponding to the scale position is stored in the special data register. You can creat

When you connect the built-in USB port of the FX3 series to the personal computer for the first time, you need to instal

To check the version of the MELSEC-F series, connect GX Works2 (personal computer) or HPP to a programmable controller,

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Controllers > Programmable Controllers MELSEC > MELSEC-F Series > Main Unit

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ Main Unit ]

11-20 of Total 126

prev 2 / 13page next

Comment display

Thecomment may not have been written tothe programmable controller. Or, the comment display setting may be required on the GX Works2 side. [Writing a com... More Details >>
- No：24681
- Release Date：2019/02/22 11:40
- Update：2019/02/22 14:15
Latch (backup) areas in the data register (D) and extended register (R) of the FX3U/FX3UC series

D200 to D7999 and R0 to R32767 can be latched. D200 to D511 can be set as non-latch areas in parameters. For details on the parameter setting, refer to the... More Details >>
- No：24699
- Release Date：2019/02/27 08:58
How to reset M8004 (Error occurrence)

Yes, it is. However, if the error cause is not eliminated, M8004 will turn on again after powering on. * How to check the error In the FX3S/FX3G/FX3GC/FX... More Details >>
- No：22280
- Release Date：2018/08/30 13:48
Station number setting in the "PLC System(2)" tab of PLC Parameter setting on GX Developer when non-protocol communication is performed

The station number setting is not required for non-protocol communication. More Details >>
- No：24948
- Release Date：2019/04/18 14:27
Using a specified bit (on/off) of a word device (D) as a condition for a contact

In the FX3U/FX3UC series, a bit in a word device can be specified. It can be specified by "Word device (D only) + Decimal point + Bit position (0 to F)". A... More Details >>
- No：22261
- Release Date：2018/08/30 13:48
Communications with a personal computer after the communication parameters for the RS-232C communication equipment are set

When a personal computer (GX Works2) is connected to the RS-232C port of a programmable controller, communications between the personal computer and the prog... More Details >>
- No：24782
- Release Date：2019/02/27 16:10
How to check the scan time (MELSEC-F series)

The present scan time is stored in D8010. Monitor the valueusing a programming tool such as GX Works2 and GX Developer. More Details >>
- No：24685
- Release Date：2019/02/22 11:40
- Update：2019/02/22 15:07
How to use variable analog potentiometers in FX3S

Numerical value data 0 to 255 corresponding tothe scale position is stored in the special data register. You can create the analog timer (volume type) by sp... More Details >>
- No：22279
- Release Date：2018/08/30 13:48
- Update：2019/02/14 10:05
Communications using the built-in USB port of the FX3 series

When you connect the built-in USB port of the FX3 series to the personal computer for the first time, you need to install the USB driver into the personal co... More Details >>
- No：22273
- Release Date：2018/08/30 13:48
How to check the version of the MELSEC-F series

To check the version of the MELSEC-F series, connect GX Works2 (personal computer) or HPP to a programmable controller, and monitor the data in D8001. The l... More Details >>
- No：24772
- Release Date：2019/02/27 15:22

11-20 of Total 126

Inquiries

page top