Connect the brake resistor to the terminal P and terminal PR. (For the FR-A700-7.5K or lower, remove the jumper of the t

The adapter is not necessary. Only the dedicated cable FR-CB20□ is required.

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switc

The forward rotation and reverse rotation are enabled by pressing the FWD/REV key on the operation panel.

The following causes are probable for persistent Err. display: 1. The terminals RES and SD are always short-circuited. 2

1. When slight imbalance (approximately 5%) is present with the inverter power supply voltage, the inverter input curren

When synchronously operating two motors, you need to detect speed from both motors. Each inverter is controlled based on

Signals input from the terminal 4 are not enabled if the terminal AU is not ON. For an inverter without the terminal AU,

It is not stored in a parameter but memorized as the frequency setting value after acceleration by the acceleration sign

Change the value of Pr.18 (High speed maximum frequency).You can set any frequency within the range defined by Pr.18.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

1001-1010 of Total 1306

prev 101 / 131page next

Brake resistor

Connect the brake resistor to the terminal P and terminal PR. (For the FR-A700-7.5K or lower, remove the jumper of the terminals PR and PX.) Do not remove th... More Details >>
- No：21333
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700PJ
FR-PA07

The adapter is not necessary. Only the dedicated cable FR-CB20□ is required. More Details >>
- No：21362
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-PA07

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switchover) is not set to "0". If it is "0... More Details >>
- No：21363
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-PA07

The forward rotation and reverse rotation are enabled by pressing the FWD/REV key on the operation panel. More Details >>
- No：21364
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Dealing with Err.

The following causes are probable for persistent Err. display: 1. The terminals RES and SD are always short-circuited. 2. Operation panel contact or operatio... More Details >>
- No：21412
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Current value on input side and output side

1. When slight imbalance (approximately 5%) is present with the inverter power supply voltage, the inverter input current can get imbalanced significantly. I... More Details >>
- No：21476
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-A200
Synchronous operation of two motors

When synchronously operating two motors, you need to detect speed from both motors. Each inverter is controlled based on this speed detection signal. As an e... More Details >>
- No：21540
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options , FREQROL-A024
Terminal

Signals input from the terminal 4 are not enabled if the terminal AU is not ON. For an inverter without the terminal AU, assign the AU function to an unused ... More Details >>
- No：21679
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

It is not stored in a parameter but memorized as the frequency setting value after acceleration by the acceleration signal.You can also choose whether or not... More Details >>
- No：21733
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Change the value of Pr.18 (High speed maximum frequency).You can set any frequency within the range defined by Pr.18. More Details >>
- No：21737
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

1001-1010 of Total 1306

Inquiries

page top