It is not possible under the dancer control. When the negative data is written, it is handled as the positive data in op

The signal becomes 0 when the RES signal is turned ON.

Because the H0F monitor only observes the ON/OFF of the hardware, it cannot be checked.

Because the multi-speed terminal is disabled, it does not operate in multi-speed.

It is one of other communication errors. The communication is not established. Check the communication settings.

Three phases are measured with the CT. The accuracy is ±10 % which is same as the inverter output current.

Yes, it can. When the FR-A7NF is installed, the CS terminal is disabled. Assign the CS terminal function to other input

No, the update cycle is not changed.

No, it cannot be connected to the RS-485 terminal. The 485 terminal supports the Mitsubishi protocol and Modbus-RTU, but

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

1001-1010 of Total 1292

prev 101 / 130page next

Dancer control during CC-Link communication

It is not possible under the dancer control. When the negative data is written, it is handled as the positive data in operation. Example) When Pr.541 is set ... More Details >>
- No：21243
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote input signal of CC-Link communication

The signal becomes 0 when the RES signal is turned ON. More Details >>
- No：21238
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Checking bit state by CC-Link communication

Because the H0F monitor only observes the ON/OFF of the hardware, it cannot be checked. More Details >>
- No：21230
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote setting function

Because the multi-speed terminal is disabled, it does not operate in multi-speed. More Details >>
- No：21205
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-SW1-SETUP

It is one of other communication errors. The communication is not established. Check the communication settings. More Details >>
- No：21176
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Engineering Software
FR-HC2

Three phases are measured with the CT. The accuracy is ±10 % which is same as the inverter output current. More Details >>
- No：21145
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
FR-A7NF

Yes, it can. When the FR-A7NF is installed, the CS terminal is disabled. Assign the CS terminal function to other input terminals by setting the parameter. B... More Details >>
- No：21121
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Plug-in Options
FR-RC

Yes. More Details >>
- No：21047
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Torque monitoring

No, the update cycle is not changed. More Details >>
- No：21044
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Operation panel

No, it cannot be connected to the RS-485 terminal. The 485 terminal supports the Mitsubishi protocol and Modbus-RTU, but it does not support the PU protocol.... More Details >>
- No：21037
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL

1001-1010 of Total 1292

Inquiries

page top