Set Pr.270 (Stop-on-contact control) to "1".Set Pr.184 (RES terminal function selection) to "3" to choose the RT signal

The following is the amount of heat generated for each capacity:0.4K: 40W 0.75K: 55W 1.5K: 90W 2.2K: 100W3.7K: 180W

It cannot be avoided by using parameters.

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (again

To set the frequency via CC-Link communication, the NET mode should be selected. The new parameter setting is applied af

No. the torque cannot be limited by using Pr.9.Set Pr.277 (Stall prevention current switching) to "1".The value of Pr.22

No parameter can be used to directly set this time.Changing Pr.9 (Electronic thermal O/L relay) changes the time.

Since the output frequency was measured, it is considered that the start signal was input correctly.Check the output vol

Since the Advanced magnetic flux vector control method uses slip compensation to compensate the frequency, the value is

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

1011-1020 of Total 1306

prev 102 / 131page next

Stop-on-contact control

Set Pr.270 (Stop-on-contact control) to "1".Set Pr.184 (RES terminal function selection) to "3" to choose the RT signal function.When the terminals RL and RT... More Details >>
- No：21691
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
FR-PA07

Yes. Use FR-CB20□. More Details >>
- No：21697
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others
FR-E740

The following is the amount of heat generated for each capacity:0.4K: 40W　　0.75K: 55W　　1.5K: 90W　　2.2K: 100W3.7K: 180W　　5.5K: 240W　　7.5K: 300W　　11K: 400W15K:... More Details >>
- No：21705
- Release Date：2018/08/22 16:29
- Category： FREQROL-E700
Electromagnetic contactor

It cannot be avoided by using parameters.　　 More Details >>
- No：21724
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Electromagnetic contactor

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (against overcurrent or overvoltage) of the... More Details >>
- No：21725
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

To set the frequency via CC-Link communication, the NET mode should be selected. The new parameter setting is applied after powering OFF and then ON the inve... More Details >>
- No：21763
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Rated motor current setting

No. the torque cannot be limited by using Pr.9.Set Pr.277 (Stall prevention current switching) to "1".The value of Pr.22 (Stall prevention operation level) w... More Details >>
- No：21766
- Release Date：2018/08/22 16:29
- Category： FREQROL-E700
Parameter

No parameter can be used to directly set this time.Changing Pr.9 (Electronic thermal O/L relay) changes the time. More Details >>
- No：21769
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Output voltage

Since the output frequency was measured, it is considered that the start signal was input correctly.Check the output voltage on the voltage monitor of the in... More Details >>
- No：21780
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Since the Advanced magnetic flux vector control method uses slip compensation to compensate the frequency, the value is not shown as exactly 60 Hz.For V/F co... More Details >>
- No：21807
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700

1011-1020 of Total 1306

Inquiries

page top