The instantaneous power failure error occurs when the power is turned ON instantaneously (within 100 ms) after the power

After inputting the start signal performing the tuning, output the output frequency. The tuning ends in approximately 5

Reverse operation is enabled by changing the setting of Pr.40.

Pr.38 of the E500 corresponds to Pr.125 (Terminal 2 frequency setting gain frequency) of D700. Pr.39 of the E500 corresp

Because the H0F monitor only observes the ON/OFF of the hardware, it cannot be checked.

They are not received during the operation. They are also not received if the command authority does not exist in the co

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rota

Reading during the operation is possible. However, when writing is performed during the operation, "rE2" (parameter writ

It is accumulated even when only the control power is ON.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

1041-1050 of Total 1292

prev 105 / 130page next

Interval of next power ON

The instantaneous power failure error occurs when the power is turned ON instantaneously (within 100 ms) after the power is turned OFF. When the motor is coa... More Details >>
- No：21388
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Magnetic flux and tuning

After inputting the start signal performing the tuning, output the output frequency. 　The tuning ends in approximately 500 ms in maximum after started. Durin... More Details >>
- No：21372
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Reverse operation

Reverse operation is enabled by changing the setting of Pr.40. More Details >>
- No：21287
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Replacement

Pr.38 of the E500 corresponds to Pr.125 (Terminal 2 frequency setting gain frequency) of D700. Pr.39 of the E500 corresponds to Pr.126 (Terminal 4 frequency ... More Details >>
- No：21254
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-D700
Checking bit state by CC-Link communication

Because the H0F monitor only observes the ON/OFF of the hardware, it cannot be checked. More Details >>
- No：21230
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

They are not received during the operation. They are also not received if the command authority does not exist in the communication. When they are executed i... More Details >>
- No：21223
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rotation command are turned OFF. More Details >>
- No：21222
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Parameter copy

Reading during the operation is possible. However, when writing is performed during the operation, "rE2" (parameter write error) occurs. More Details >>
- No：21215
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Carrier frequency

It is fixed to 5 kHz. More Details >>
- No：21211
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Cumulative energization time

It is accumulated even when only the control power is ON. More Details >>
- No：21208
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

1041-1050 of Total 1292

Inquiries

page top