The noise filter is not built-in the FR-E700 series. It is built in the FR-A700/F700 series with the 55K or lower capaci

The ferrule terminal or single wire can be used for the control circuit wiring.

When the built-in brake resistor is used, the regenerative brake duty is as follows:200 V 0.4K to 3.7K: 3%, 5.5K to 7.5K

No, Real sensorless vector control cannot be used in the FR-E700.

No, it is not changed. Pr.268 is the parameter for the operation panel.

No error will occur because up to 400 Hz that is the upper limit of the setting range can be written.

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is rever

Reading during the operation is possible. However, when writing is performed during the operation, "rE2" (parameter writ

No. During JOG operation, deceleration stop is performed even though Pr.250 is set.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

1071-1080 of Total 1292

prev 108 / 130page next

Noise filter

The noise filter is not built-in the FR-E700 series. It is built in the FR-A700/F700 series with the 55K or lower capacity. More Details >>
- No：21276
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
Wiring and terminal

The ferrule terminal or single wire can be used for the control circuit wiring. More Details >>
- No：21275
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
Brake resistor

When the built-in brake resistor is used, the regenerative brake duty is as follows:200 V 0.4K to 3.7K: 3%, 5.5K to 7.5K: 2%400 V 0.4K to 7.5K: 2 % The capac... More Details >>
- No：21273
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
Real sensorless vector control

No, Real sensorless vector control cannot be used in the FR-E700. More Details >>
- No：21269
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
FR-A7NC (E kit)

They are insulated. More Details >>
- No：21242
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Pr.268 (Monitor decimal digits selection) during CC-Link communication

No, it is not changed. Pr.268 is the parameter for the operation panel. More Details >>
- No：21241
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Writing set frequency by CC-Link communication

No error will occur because up to 400 Hz that is the upper limit of the setting range can be written. More Details >>
- No：21229
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is reversed. - The signal from the encoder is... More Details >>
- No：21219
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Parameter copy

Reading during the operation is possible. However, when writing is performed during the operation, "rE2" (parameter write error) occurs. More Details >>
- No：21215
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Stop selection

No. During JOG operation, deceleration stop is performed even though Pr.250 is set. More Details >>
- No：21199
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

1071-1080 of Total 1292

Inquiries

page top