The communication is established if DA, DB, and DG are connected each other.

Because the H0F monitor only observes the ON/OFF of the hardware, it cannot be checked.

It is tilted to wire the cable easily.

Other than "0" can be input. The inverter is reset by writing any numerical value.

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

When the second torque limit is used, the settings of Pr.816 and 817 are valid.

There is no setting to disable it, but setting a high torque limit level such as 400 % can disable the limit.

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur wh

It is fundamentally the same as the conventional model. Considering the recent safety awareness growth, we decided to st

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

1141-1150 of Total 1292

prev 115 / 130page next

Wiring of CC-Link communication cable

The communication is established if DA, DB, and DG are connected each other. More Details >>
- No：21239
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Checking bit state by CC-Link communication

Because the H0F monitor only observes the ON/OFF of the hardware, it cannot be checked. More Details >>
- No：21230
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-A7NCE connector

It is tilted to wire the cable easily. More Details >>
- No：21228
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

Other than "0" can be input. The inverter is reset by writing any numerical value. More Details >>
- No：21224
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Torque limit

When the second torque limit is used, the settings of Pr.816 and 817 are valid. More Details >>
- No：21218
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Torque limit

There is no setting to disable it, but setting a high torque limit level such as 400 % can disable the limit. More Details >>
- No：21217
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
IPM motor drive

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur when the load inertia is too high. As a... More Details >>
- No：21216
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-HC2

It is fundamentally the same as the conventional model. Considering the recent safety awareness growth, we decided to start supporting it from the FR-HC2. Be... More Details >>
- No：21212
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Leakage current

It is 1 mA as the 700 series. More Details >>
- No：21204
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

1141-1150 of Total 1292

Inquiries

page top