The detection level of the output current value cannot be changed using a potentiometer or a similar device.

Since the output frequency was measured, it is considered that the start signal was input correctly.Check the output vol

Yes, you can set them randomly.

Check the setting of Pr.79 (Operation mode).If the setting value is "2", frequency commands from an external terminal is

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note t

The parameters used when the terminal 4 is used are C5, C6, 126, and C7.Set Pr.C5 (Terminal 4 frequency setting bias fre

Set the rated frequency of the motor used to it.

Set Pr.79 (Operation mode) to "1" (PU operation mode).

When the frequency is set using the setting dial, it is not necessary to set it again.The inverter memorizes the setting

You also need to set Pr.79 (Operation mode) to "3".

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

1181-1190 of Total 1306

prev 119 / 131page next

Output current value

The detection level of the output current value cannot be changed using a potentiometer or a similar device.　　 More Details >>
- No：21779
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Output voltage

Since the output frequency was measured, it is considered that the start signal was input correctly.Check the output voltage on the voltage monitor of the in... More Details >>
- No：21780
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Yes, you can set them randomly.　　 More Details >>
- No：21796
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Check the setting of Pr.79 (Operation mode).If the setting value is "2", frequency commands from an external terminal is effective and the frequency setting ... More Details >>
- No：21797
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note that this terminal AU is not prepared ... More Details >>
- No：21799
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

The parameters used when the terminal 4 is used are C5, C6, 126, and C7.Set Pr.C5 (Terminal 4 frequency setting bias frequency) while feeding a current signa... More Details >>
- No：21800
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Base frequency setting value

Set the rated frequency of the motor used to it.　 More Details >>
- No：21814
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Operation stop, frequency setting

Set Pr.79 (Operation mode) to "1" (PU operation mode).　 More Details >>
- No：21819
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

When the frequency is set using the setting dial, it is not necessary to set it again.The inverter memorizes the setting value internally even after the powe... More Details >>
- No：21842
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Control terminal

You also need to set Pr.79 (Operation mode) to "3". More Details >>
- No：21844
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

1181-1190 of Total 1306

Inquiries

page top