No. Writing is not available when the model is different. Writing the parameter copy file using a USB memory device is a

Check that Pr.3 (Base frequency) is set to "200 Hz". Adjust Pr.0 (Torque boost) as necessary.

An inverter is used to rotate a motor but it cannot be used to detect whether the belt is broken or not. However, the ma

The inverter uses PWM control to change the output voltage and frequency to vary the motor speed. PWM stands for Pulse W

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you

The FR-E700, D700, F700PJ may activate input phase loss protection "E.ILF" if the phase-to-phase voltage of the power su

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (

The FREQROL-A200 has magnetic flux vector control in addition to the conventional V/F control. Magnetic flux vector cont

The possible causes are as follows. While the inverter power supply is turned ON, inserting the modular jack to the conn

The inverter has the current limit function. This automatically controls the frequency so that the preset current value

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

1251-1260 of Total 1292

prev 126 / 130page next

Parameter copy to the USB memory

No. Writing is not available when the model is different. Writing the parameter copy file using a USB memory device is available only for the same models. Ot... More Details >>
- No：21014
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
Rated frequency setting

Check that Pr.3 (Base frequency) is set to "200 Hz". Adjust Pr.0 (Torque boost) as necessary. More Details >>
- No：21280
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Detection of the motor load

An inverter is used to rotate a motor but it cannot be used to detect whether the belt is broken or not. However, the magnitude of the load will change when ... More Details >>
- No：21387
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Soft-PWM

The inverter uses PWM control to change the output voltage and frequency to vary the motor speed. PWM stands for Pulse Width Modulation. Voltage is chopped i... More Details >>
- No：21549
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Calculation of acceleration/deceleration time

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you should consider a factor of 120% for ... More Details >>
- No：21965
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
Input phase loss

The FR-E700, D700, F700PJ may activate input phase loss protection "E.ILF" if the phase-to-phase voltage of the power supply has become largely unbalanced. More Details >>
- No：21339
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Difference between SU (up to frequency) and FU (frequency detection)

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (the frequency the inverter is require... More Details >>
- No：21436
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Auto tuning, tuning mode

The FREQROL-A200 has magnetic flux vector control in addition to the conventional V/F control. Magnetic flux vector control controls the motor with higher ac... More Details >>
- No：21637
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A200
Communication fault occurs

The possible causes are as follows. While the inverter power supply is turned ON, inserting the modular jack to the connector with the operation panel remove... More Details >>
- No：22094
- Release Date：2018/08/22 16:30
- Category： Engineering Software
Automatic overload control of inverter

The inverter has the current limit function. This automatically controls the frequency so that the preset current value may not be exceeded. (Note that the m... More Details >>
- No：21409
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-F500 , FREQROL-E500 , FREQROL-S500

1251-1260 of Total 1292

Inquiries

page top