1. You can implement stop-on-contact.2. When implementing stop-on-contact, use the inverter to decelerate the motors to

It seems that there is a read error for 20 mA DC inside the inverter.Setting Pr.905 to 50 Hz while 20 mA DC is actually

Set the parameters below. For other parameters, keep the initial settings.1. Set Pr.122 (Communication check time interv

1. ACL has the input power factor of approximately 90% and DCL has the input power factor of approximately 95%. Therefor

As the inverter does not display the speed in m/min, let us explain using the speed display in r/min. In this case, set

Change Pr.79 (Operation mode) to "3" (Combined operation mode) and short-circuit the external terminals STF and SD (or S

The power supply voltage may have dropped.Read the converter output voltage monitor (Pr.55 = 8) and check if Converter o

1. Use the external terminals STF, RL, and SD. (A push-ON switch for operation is required between the terminals STF and

Priorities are: Low speed (RL) > Middle speed (RM) > High speed (RH).For example, if the low speed (RL) and middle

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch whil

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

121-130 of Total 1306

prev 13 / 131page next

Stop-on-contact control

1. You can implement stop-on-contact.2. When implementing stop-on-contact, use the inverter to decelerate the motors to reduce the impact upon stop-on-contac... More Details >>
- No：22041
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Speed control failure due to 20 mA from DC 4

It seems that there is a read error for 20 mA DC inside the inverter.Setting Pr.905 to 50 Hz while 20 mA DC is actually flowing between the terminals 4 and 5... More Details >>
- No：21998
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-F500 , FREQROL-E500 , FREQROL-A200 , FREQROL-A100
Inverter setup

Set the parameters below. For other parameters, keep the initial settings.1.　Set Pr.122 (Communication check time interval) to other than "0". ("9999" is OK.... More Details >>
- No：21986
- Release Date：2018/08/22 16:30
- Category： Engineering Software
Proper use of AC reactor and DC reactor

1. ACL has the input power factor of approximately 90% and DCL has the input power factor of approximately 95%. Therefore, DCL has a higher input power facto... More Details >>
- No：21949
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
I want to display the speed on an analog meter.

As the inverter does not display the speed in m/min, let us explain using the speed display in r/min. In this case, set Pr.52 to "6" (operation panel display... More Details >>
- No：21944
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Parameter setting

Change Pr.79 (Operation mode) to "3" (Combined operation mode) and short-circuit the external terminals STF and SD (or STR and SD for reverse rotation). More Details >>
- No：21859
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Running frequency

The power supply voltage may have dropped.Read the converter output voltage monitor (Pr.55 = 8) and check if Converter output voltage monitor/√2 is within th... More Details >>
- No：21820
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
External terminal

1. Use the external terminals STF, RL, and SD. (A push-ON switch for operation is required between the terminals STF and SD, and a push-OFF switch is require... More Details >>
- No：21816
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Multi-speed setting

Priorities are: Low speed (RL) > Middle speed (RM) > High speed (RH).For example, if the low speed (RL) and middle speed (RM) signals are input simulta... More Details >>
- No：21772
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Switching between external operation and NET operation

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch while Pr.79 (Operation mode) is set to "6... More Details >>
- No：21688
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

121-130 of Total 1306

Inquiries

page top