The following two major countermeasures against noise are available: - Keep the noise source and partner device apart fr

The whole system consists of the power supply, molded case circuit breaker, high power factor converter, inverter, and m

1. Such a behavior does not usually happen. (1) The operation command (STF) is not input, contact faults are present, o

No load current for each power supply voltage is as follows:- Approximately 15.5 A for 200 VAC 60 Hz- Approximately 21.7

Connect the external potentiometer to the terminals 10, 2, and 5 of the first inverter (be sure to connect the variable

The inverter alarm "OV3" occurs when the main circuit DC voltage inside the inverter goes higher than the preset value d

Frequent occurrences of OL means that the inverter is overloaded. Since the inverter can go faulty if it is constantly o

When auto tuning completes normally, the setting value of Pr.96 (Auto tuning setting/status) is changed to "3". When it

When carrying out the megger test of the inverter, shorten all the terminals R, S, T, U, V, and W of the main circuit an

The FR-E700 is not supported by FR-SW2-SETUP-WJ. The FR-E700 series are supported by FR-SW3-SETUP-WJ. This software can

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

141-150 of Total 1306

prev 15 / 131page next

Countermeasure against noise and leakage current during low-noise operation

The following two major countermeasures against noise are available: - Keep the noise source and partner device apart from each other.- Install a noise filte... More Details >>
- No：21605
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
System configuration

The whole system consists of the power supply, molded case circuit breaker, high power factor converter, inverter, and motor. The high power factor converter... More Details >>
- No：21575
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Inverter output stop

1. Such a behavior does not usually happen. 　(1) The operation command (STF) is not input, contact faults are present, or wire is broken. 　(2) The output shu... More Details >>
- No：21552
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
No load current value of motor

No load current for each power supply voltage is as follows:- Approximately 15.5 A for 200 VAC 60 Hz- Approximately 21.7 A for 220 VAC 60 HzThe current is es... More Details >>
- No：21534
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others
Connecting potentiometer

Connect the external potentiometer to the terminals 10, 2, and 5 of the first inverter (be sure to connect the variable terminal to the terminal 2).　Connect ... More Details >>
- No：21462
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Countermeasure against error

The inverter alarm "OV3" occurs when the main circuit DC voltage inside the inverter goes higher than the preset value due to the regenerative power returned... More Details >>
- No：21438
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A024
Overcurrent

Frequent occurrences of OL means that the inverter is overloaded. Since the inverter can go faulty if it is constantly overloaded, you need to take a counter... More Details >>
- No：21430
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Offline auto tuning

When auto tuning completes normally, the setting value of Pr.96 (Auto tuning setting/status) is changed to "3". When it is not changed, check the set paramet... More Details >>
- No：21353
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700PJ
Megger test

When carrying out the megger test of the inverter, shorten all the terminals R, S, T, U, V, and W of the main circuit and use the 500 VDC megger for earth. D... More Details >>
- No：21327
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Supported model for FR-Configurator

The FR-E700 is not supported by FR-SW2-SETUP-WJ. The FR-E700 series are supported by FR-SW3-SETUP-WJ. This software can be downloaded from the Mitsubishi Ele... More Details >>
- No：21314
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

141-150 of Total 1306

Inquiries

page top