When the brake sequence function is enabled, the RT signal is disabled and the stop-on-contact control cannot be perform

It is not output in the JOG operation mode.

When the second torque limit is used, the settings of Pr.816 and 817 are valid.

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is rever

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

The signal becomes 0 when the RES signal is turned ON.

Pr.38 of the E500 corresponds to Pr.125 (Terminal 2 frequency setting gain frequency) of D700. Pr.39 of the E500 corresp

It can be driven by connecting single-phase 200 V to the terminals R and S. In this case, the load current must be one-t

Yes. The model is FR-E710W. The input is single-phase 100 V, but the output is three-phase 200 V.

Check the setting value of Pr.73. Or check Pr.C4 (Terminal 2 frequency setting gain) for the percentage of the voltage t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

161-170 of Total 1306

prev 17 / 131page next

Stop-on-contact control

When the brake sequence function is enabled, the RT signal is disabled and the stop-on-contact control cannot be performed. More Details >>
- No：21209
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
PU signal

It is not output in the JOG operation mode. More Details >>
- No：21214
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Torque limit

When the second torque limit is used, the settings of Pr.816 and 817 are valid. More Details >>
- No：21218
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is reversed. - The signal from the encoder is... More Details >>
- No：21219
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote input signal of CC-Link communication

The signal becomes 0 when the RES signal is turned ON. More Details >>
- No：21238
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Replacement

Pr.38 of the E500 corresponds to Pr.125 (Terminal 2 frequency setting gain frequency) of D700. Pr.39 of the E500 corresponds to Pr.126 (Terminal 4 frequency ... More Details >>
- No：21254
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-D700
Specifications

It can be driven by connecting single-phase 200 V to the terminals R and S. In this case, the load current must be one-third or less of the inverter rated cu... More Details >>
- No：21282
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
FR-E710W

Yes. The model is FR-E710W. The input is single-phase 100 V, but the output is three-phase 200 V. More Details >>
- No：21320
- Release Date：2018/08/22 16:27
- Category： FREQROL-E700
Analog voltage

Check the setting value of Pr.73. Or check Pr.C4 (Terminal 2 frequency setting gain) for the percentage of the voltage that is actually applied. For the FR-E... More Details >>
- No：21356
- Release Date：2018/08/22 16:27
- Category： FREQROL-E700

161-170 of Total 1306

Inquiries

page top