If the command is 0.01 Hz or higher, the positioning control is performed.

It is not activated because the function itself is disabled.

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur wh

The high speed command (multi-speed command) is prioritized over the frequency setting potentiometer. It is OK if these

If you connect two frequency setting potentiometers to the terminals 5 and 10, the permissible current of 10 mA is excee

You can drive the motor with the FR-V240E-5.5K. However, the following conditions apply: - You need to perform auto tuni

Yes, you can use the 10BASE-T cable (straight) with the E500.

Winding diameter calculation is available for all controls (dancer feedback speed control, tension sensor feedback speed

Save the parameter file (.rpm) after reading the system file (.mel) created in SW1. With the saved parameter file (.rpm)

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

191-200 of Total 1306

prev 20 / 131page next

MM-FR-A800

If the command is 0.01 Hz or higher, the positioning control is performed. More Details >>
- No：21001
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
Fast-response current limit

It is not activated because the function itself is disabled. More Details >>
- No：21137
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
IPM motor drive

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur when the load inertia is too high. As a... More Details >>
- No：21216
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Speed setting

The high speed command (multi-speed command) is prioritized over the frequency setting potentiometer. It is OK if these are both input simultaneously. When t... More Details >>
- No：21424
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-U100
Auxiliary input power supply

If you connect two frequency setting potentiometers to the terminals 5 and 10, the permissible current of 10 mA is exceeded, and you need to install 2 KΩ res... More Details >>
- No：21494
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
I want to drive other manufacturer's motor with PG

You can drive the motor with the FR-V240E-5.5K. However, the following conditions apply: - You need to perform auto tuning because the motor's circuit consta... More Details >>
- No：21539
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-V200
Operation panel extension cable

Yes, you can use the 10BASE-T cable (straight) with the E500. More Details >>
- No：22085
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
FR-A800-R2R

Winding diameter calculation is available for all controls (dancer feedback speed control, tension sensor feedback speed control, tension sensorless torque c... More Details >>
- No：20886
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
FR-A8TP

Yes. More Details >>
- No：21038
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR Configurator

Save the parameter file (.rpm) after reading the system file (.mel) created in SW1. With the saved parameter file (.rpm), the parameter of the 700 series can... More Details >>
- No：21141
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Engineering Software

191-200 of Total 1306

Inquiries

page top