The high speed command (multi-speed command) is prioritized over the frequency setting potentiometer. It is OK if these

"E.OV3" is displayed when the voltage between the inverter terminals PN rises abnormally high while the inverter is dece

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro

Press the "MODE" key on the operation panel several times to display "P.0" and parameter setting screen. Then turn the s

Check the version of FR-Configurator (FR-SW3-SETUP-WJ). If the version is "1.00", it does not support or detect the FR-E

Normally, the auto tuning condition depends on the combination of the inverter and motor (including wiring to the motor)

Calibrate C6 (Pr.904) (Terminal 4 frequency setting bias frequency) and C7 (Pr.905) (Terminal 4 frequency setting gain f

The standby power of the FR-F700PJ series (with filterpack) is registered in member's page of Mitsubishi Electric FA Glo

Only the V/F control is related with Pr.56. The motor torque is calculated from the current value (not Pr.56) and motor

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

191-200 of Total 1306

prev 20 / 131page next

Speed setting

The high speed command (multi-speed command) is prioritized over the frequency setting potentiometer. It is OK if these are both input simultaneously. When t... More Details >>
- No：21424
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-U100
Fault display

"E.OV3" is displayed when the voltage between the inverter terminals PN rises abnormally high while the inverter is decelerating or stopped. In this case, th... More Details >>
- No：21411
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A024
Driving 200 V motor by 400 V inverter

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro surge". Usually this surge voltage i... More Details >>
- No：21403
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Parameter

Press the "MODE" key on the operation panel several times to display "P.0" and parameter setting screen. Then turn the setting dial to display "C..." screen ... More Details >>
- No：21336
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Model setting in FR-Configurator

Check the version of FR-Configurator (FR-SW3-SETUP-WJ). If the version is "1.00", it does not support or detect the FR-E740. Version "2.00" supports the FR-E... More Details >>
- No：21309
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Auto tuning

Normally, the auto tuning condition depends on the combination of the inverter and motor (including wiring to the motor), perform auto tuning each time. The ... More Details >>
- No：21293
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700PJ
Frequency setting signal

Calibrate C6 (Pr.904) (Terminal 4 frequency setting bias frequency) and C7 (Pr.905) (Terminal 4 frequency setting gain frequency). If the situation does not ... More Details >>
- No：21265
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Standby power

The standby power of the FR-F700PJ series (with filterpack) is registered in member's page of Mitsubishi Electric FA Global Website. Refer to the Technical N... More Details >>
- No：21210
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-B/FR-B3

Yes. More Details >>
- No：21063
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , Others , FREQROL-B
Load characteristics fault detection

Only the V/F control is related with Pr.56. The motor torque is calculated from the current value (not Pr.56) and motor constant. For the V/F control, it is ... More Details >>
- No：20893
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-F800

191-200 of Total 1306

Inquiries

page top