Under a 50% torque limit, if the commanded speed (50 Hz in your example) cannot be achieved without torque exceeding 50%

1. Yes. 2. Set Pr.17 to "2". 3. If the start signal is ON, the operation continues even the emergency stop is OFF.

When Pr.79 is set to "3", since the start command is in the External operation mode, the RUN key of FR-PA07 does not wor

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542

Pr.77 and 79 cannot be changed via CC-Link communication.

The FR-PU07(BB) can be used with some restrictions.* The major restrictions are as follows. - Pr.1000 or later cannot be

No. (Using the copy function causes an error.) Use the FR-DU08 when performing the copy function of the operation panel.

It is said that the EEPROM has a lifetime of 100,000 write cycles. When the data is written every time the frequency cha

Do not carry out a pressure test. As for a megger test, carry out the test with 500 VDC as describes in the Instruction

No, it cannot. The standard operation panel (FR-DU08) can be connected to the face of the board by using the FR-ADP (ope

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

231-240 of Total 1306

prev 24 / 131page next

Operation under torque limit in the speed control mode

Under a 50% torque limit, if the commanded speed (50 Hz in your example) cannot be achieved without torque exceeding 50%, since the torque does not exceed th... More Details >>
- No：21483
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
PU operation

1. Yes. 2. Set Pr.17 to "2". 　3. If the start signal is ON, the operation continues even the emergency stop is OFF. More Details >>
- No：21359
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-PA07

When Pr.79 is set to "3", since the start command is in the External operation mode, the RUN key of FR-PA07 does not work. More Details >>
- No：21303
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Replacement

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542 (Communication station number (CC-Lin... More Details >>
- No：21248
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
FR Configurator SW3 (CC-Link Seamless)

Pr.77 and 79 cannot be changed via CC-Link communication. More Details >>
- No：21174
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Engineering Software
Parameter unit

The FR-PU07(BB) can be used with some restrictions.* The major restrictions are as follows. - Pr.1000 or later cannot be set. - Alarms or warnings that are a... More Details >>
- No：21119
- Release Date：2018/08/22 16:26
- Category： FREQROL-A800 , Options , FREQROL-F800
Copy function

No. (Using the copy function causes an error.) Use the FR-DU08 when performing the copy function of the operation panel. More Details >>
- No：21118
- Release Date：2018/08/22 16:26
- Category： FREQROL-A800 , Options , FREQROL-F800
The lifetime of EEPROM write

It is said that the EEPROM has a lifetime of 100,000 write cycles. When the data is written every time the frequency changes, the life of the EEPROM may not ... More Details >>
- No：20996
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800 , FREQROL-E700 , FREQROL-D700
FR-HC2

Do not carry out a pressure test. As for a megger test, carry out the test with 500 VDC as describes in the Instruction Manual of the inverter. More Details >>
- No：20967
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Others , Peripheral devices
FR-PA07

No, it cannot. The standard operation panel (FR-DU08) can be connected to the face of the board by using the FR-ADP (operation panel connection connector) an... More Details >>
- No：20898
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options , FREQROL-A800 , FREQROL-F800

231-240 of Total 1306

Inquiries

page top