For the set frequency 60 Hz, ±6 Hz is applied and thus the up to frequency signal is output between 54 Hz and 66 Hz. Dur

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform.

By setting Pr.160 (User group read selection ("Extended function display selection" for D700)) to "0", all the parameter

The inverter restart operation is disabled at turn-OFF of the CS signal while a value other than "9999" (with restart) i

Since the initial value of Pr.13 (Starting frequency) is 0.5 Hz, the operation does not start unless 0.5 Hz or higher fr

It is not switched. The frequency at the fault saved in the faults history is always displayed in frequency [Hz].

A radio noise filter can be used with a built-in filter.

The ON level is the power supply voltage -3 V or higher and the OFF level is 3 V or lower.

Our suggestion is to adjust the following parameters:1. Set Pr.14 = 0. If the V/F pattern for variable-torque load (Pr.1

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

341-350 of Total 1292

prev 35 / 130page next

Frequency setting

For the set frequency 60 Hz, ±6 Hz is applied and thus the up to frequency signal is output between 54 Hz and 66 Hz. During acceleration/deceleration to the ... More Details >>
- No：21348
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Terminal indicator lamp

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform. Check if the lamp to be connected ca... More Details >>
- No：21323
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Parameter read

By setting Pr.160 (User group read selection ("Extended function display selection" for D700)) to "0", all the parameters can be read. More Details >>
- No：21262
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Automatic restart after instantaneous power failure

The inverter restart operation is disabled at turn-OFF of the CS signal while a value other than "9999" (with restart) is set in Pr.57. The terminals CS and ... More Details >>
- No：21255
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Frequency command

Since the initial value of Pr.13 (Starting frequency) is 0.5 Hz, the operation does not start unless 0.5 Hz or higher frequency is set. When 0.49 Hz is set i... More Details >>
- No：21251
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Rotation speed display

It is not switched. The frequency at the fault saved in the faults history is always displayed in frequency [Hz]. More Details >>
- No：21180
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Radio noise filter (FR-BIF)

A radio noise filter can be used with a built-in filter. More Details >>
- No：21113
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , Options , FREQROL-F800
FR-A8AP

The ON level is the power supply voltage -3 V or higher and the OFF level is 3 V or lower. More Details >>
- No：21002
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , Plug-in Options
Insulation level of the MM-EFS

F class (155 deg C) More Details >>
- No：20809
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Others
Frequency does not rise with blower

Our suggestion is to adjust the following parameters:1. Set Pr.14 = 0. If the V/F pattern for variable-torque load (Pr.14 = 1) is used, the current may incre... More Details >>
- No：22060
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-F500

341-350 of Total 1292

Inquiries

page top