Yes. The single-phase 200 V can be input. If the single-phase input is performed when Pr.872 (Input phase loss protectio

Set Pr.55 (Frequency monitoring reference) of the first inverter to 70 Hz.

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset t

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542

Set Pr.71 (Applied motor), Pr.80 (Motor capacity), Pr.81 (Number of motor poles), and Pr.800 (Control method selection).

Use the FR-A740. Basically, select the capacity according to the calculation result of "rated inverter output current ?

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is rever

There is no setting to disable it, but setting a high torque limit level such as 400 % can disable the limit.

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur wh

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

361-370 of Total 1306

prev 37 / 131page next

Parameter setting

Yes. The single-phase 200 V can be input. If the single-phase input is performed when Pr.872 (Input phase loss protection) is set to "1", the input phase los... More Details >>
- No：21270
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
AM terminal output

Set Pr.55 (Frequency monitoring reference) of the first inverter to 70 Hz. More Details >>
- No：21257
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link communication

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset the inverter (or power ON again) to st... More Details >>
- No：21256
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Replacement

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542 (Communication station number (CC-Lin... More Details >>
- No：21248
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Changing the control method

Set Pr.71 (Applied motor), Pr.80 (Motor capacity), Pr.81 (Number of motor poles), and Pr.800 (Control method selection). More Details >>
- No：21245
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Model selection

Use the FR-A740. Basically, select the capacity according to the calculation result of "rated inverter output current ? rated motor current × 1.1". More Details >>
- No：21244
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Remote register when instruction code execution request is issued at CC-Link communication

The value "0" is stored. More Details >>
- No：21234
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is reversed. - The signal from the encoder is... More Details >>
- No：21219
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Torque limit

There is no setting to disable it, but setting a high torque limit level such as 400 % can disable the limit. More Details >>
- No：21217
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
IPM motor drive

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur when the load inertia is too high. As a... More Details >>
- No：21216
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

361-370 of Total 1306

Inquiries

page top