For the normal type (FR-B3) is 2 KHz. For the low-noise type (FR-B3-N), 14.5 KHz.

The NC contact does not open when the power supply is cut off whether the inverter is operating or ceased.When the input

You can switch between the NET mode and external operation.Assign the X66 signal (Operation switching) to an unused term

Check if signals that are ON when the programmable controller's transistor output starts are always ON.

Set Pr.125 (Terminal 2 frequency setting gain frequency) instead of Pr.1 (Maximum frequency).

Check the setting of Pr.79 (Operation mode).If the setting value is "2", frequency commands from an external terminal is

Set Pr.52 (PU/DU main display data selection) to "5".Set the monitor as the third monitor, frequency -> current ->

Pr.1 (Maximum frequency) and Pr.18 (Maximum frequency).

Even while the inverter is operating, you can use the setting dial to change the frequency and then press the SET key an

No. You cannot change the setting during operation.However, setting Pr.77 (Parameter write selection) to "2" allows for

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

371-380 of Total 1306

prev 38 / 131page next

Setting value of Pr.72 (FR-B, B3 (A800 base))

For the normal type (FR-B3) is 2 KHz. For the low-noise type (FR-B3-N), 14.5 KHz. More Details >>
- No：20828
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-B
Fault contact state when input side power supply is cut off

The NC contact does not open when the power supply is cut off whether the inverter is operating or ceased.When the input side power supply is cut off, the DC... More Details >>
- No：21958
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
NET mode, external operation switching

You can switch between the NET mode and external operation.Assign the X66 signal (Operation switching) to an unused terminal for switching.Also, set Pr.79 (O... More Details >>
- No：21906
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Transistor output module of the programmable controller

Check if signals that are ON when the programmable controller's transistor output starts are always ON. More Details >>
- No：21811
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) instead of Pr.1 (Maximum frequency).　　 More Details >>
- No：21802
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Check the setting of Pr.79 (Operation mode).If the setting value is "2", frequency commands from an external terminal is effective and the frequency setting ... More Details >>
- No：21797
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency, monitor setting

Set Pr.52 (PU/DU main display data selection) to "5".Set the monitor as the third monitor, frequency -> current -> setting frequency. More Details >>
- No：21745
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Pr.1 (Maximum frequency) and Pr.18 (Maximum frequency).　　 More Details >>
- No：21744
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Even while the inverter is operating, you can use the setting dial to change the frequency and then press the SET key and the inverter operates at the new fr... More Details >>
- No：21739
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

No. You cannot change the setting during operation.However, setting Pr.77 (Parameter write selection) to "2" allows for the setting change during operation. ... More Details >>
- No：21734
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

371-380 of Total 1306

Inquiries

page top