1. As the measurement condition is unknown, the possible cases are as follows: - If you measured the current on the inp

I cannot tell whether or not you can drive the motor because the electrical specifications are not clear. It is conside

When the carrier frequency increases, noise and leakage current increase accordingly. To prevent the noise and leakage c

The ST1 is a setting file and the TR1 is a waveform file.

Yes, the circuit board coating and conductive plating are applied to the HC2 as standard.

No, the MT-BU5 is unavailable because it is the conventional model. Use the FR-BU2.

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur wh

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rota

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated fo

It is not possible when the speed command is communication.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

31-40 of Total 1292

prev 4 / 130page next

Inverter current value

1. As the measurement condition is unknown, the possible cases are as follows: - If you measured the current on the input side of the inverter, since the cu... More Details >>
- No：21457
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Driving German pole change motor by inverter

I cannot tell whether or not you can drive the motor because the electrical specifications are not clear. 　It is considered that you may drive the pole chang... More Details >>
- No：21518
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Noise and leakage current (tone modulation control) of low-noise series

When the carrier frequency increases, noise and leakage current increase accordingly. To prevent the noise and leakage current from increasing while keeping ... More Details >>
- No：21599
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-U100
Trace function

The ST1 is a setting file and the TR1 is a waveform file. More Details >>
- No：20896
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
FR-HC2

Yes, the circuit board coating and conductive plating are applied to the HC2 as standard. More Details >>
- No：21026
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
MT-BU5

No, the MT-BU5 is unavailable because it is the conventional model. Use the FR-BU2. More Details >>
- No：21046
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
IPM motor drive

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur when the load inertia is too high. As a... More Details >>
- No：21216
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rotation command are turned OFF. More Details >>
- No：21222
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Inverter installation when using the FR-A7NCE

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated for 5 cm or more to pass the cable. More Details >>
- No：21227
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Speed command by CC-Link communication

It is not possible when the speed command is communication. More Details >>
- No：21232
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

31-40 of Total 1292

Inquiries

page top