Yes, the circuit board coating and conductive plating are applied to the HC2 as standard.

No, the MT-BU5 is unavailable because it is the conventional model. Use the FR-BU2.

Under Real sensorless vector control, the maximum wiring length is 500 m. Under Vector control with encoder, the maximum

There is no regulation value. Use the inverters in the environment without corrosive gas.

When the brake sequence function is enabled, the RT signal is disabled and the stop-on-contact control cannot be perform

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur wh

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is rever

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rota

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

51-60 of Total 1306

prev 6 / 131page next

FR-HC2

Yes, the circuit board coating and conductive plating are applied to the HC2 as standard. More Details >>
- No：21026
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
MT-BU5

No, the MT-BU5 is unavailable because it is the conventional model. Use the FR-BU2. More Details >>
- No：21046
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Wiring length

Under Real sensorless vector control, the maximum wiring length is 500 m. Under Vector control with encoder, the maximum wiring length is 100 m. More Details >>
- No：21133
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
Installation environment

There is no regulation value. Use the inverters in the environment without corrosive gas. More Details >>
- No：21201
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Stop-on-contact control

When the brake sequence function is enabled, the RT signal is disabled and the stop-on-contact control cannot be performed. More Details >>
- No：21209
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Carrier frequency

It is fixed to 5 kHz. More Details >>
- No：21211
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
IPM motor drive

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur when the load inertia is too high. As a... More Details >>
- No：21216
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is reversed. - The signal from the encoder is... More Details >>
- No：21219
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

It decelerates and stops. The operation is the same as the one when the Bit of forward rotation command and reverse rotation command are turned OFF. More Details >>
- No：21222
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

51-60 of Total 1306

Inquiries

page top