For the V/F control and Advanced magnetic flux vector control, the FR-A800 stops only by Pr.1103 Deceleration time at em

For the normal type (FR-B3) is 2 KHz. For the low-noise type (FR-B3-N), 14.5 KHz.

Yes, it can. Set "12" or "112" to the MM-EFS capacity used for Pr.80 (Motor capacity) and Pr.998 (PM parameter initializ

The power factor is 0.99 or more (at rated load).

- Both 200 V and 400 V can be used only with the capacity 22 kW or higher. - The rated current (capacity) is derated. (F

Square wave input is not recommended since it can cause failures (for example, damage the diode bridge).

It is considered that malfunction of the measurement device is due to noise. Check the noise propagation route since the

If the MC on the input side is shut off using the fault output of the FR-E500, the inverter's fault records are left in

The FREQROL-F500 series has been already supported by the setup software released since February 2000.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

671-680 of Total 1306

prev 68 / 131page next

Emergency stop of the FR-A800

For the V/F control and Advanced magnetic flux vector control, the FR-A800 stops only by Pr.1103 Deceleration time at emergency stop. Pr.815 is not affected. More Details >>
- No：20860
- Release Date：2018/08/22 16:24
- Category： FREQROL-A800
FR-A800-GF/FR-A800-E

Yes, they can. More Details >>
- No：20856
- Release Date：2018/08/22 16:24
- Category： FREQROL-A800
Setting value of Pr.72 (FR-B, B3 (A800 base))

For the normal type (FR-B3) is 2 KHz. For the low-noise type (FR-B3-N), 14.5 KHz. More Details >>
- No：20828
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-B
Combination of the FR-F800 and MM-EFS

Yes, it can. Set "12" or "112" to the MM-EFS capacity used for Pr.80 (Motor capacity) and Pr.998 (PM parameter initialization). More Details >>
- No：20820
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-F800
FR-XC

The power factor is 0.99 or more (at rated load). More Details >>
- No：20803
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
FR-XC

- Both 200 V and 400 V can be used only with the capacity 22 kW or higher. - The rated current (capacity) is derated. (For the detail, refer to the Instructi... More Details >>
- No：20802
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
Inverter input power supply

Square wave input is not recommended since it can cause failures (for example, damage the diode bridge). More Details >>
- No：22106
- Release Date：2018/08/22 16:31
- Category： Inverters-FREQROL , FREQROL-E500
Influence on external measurement device

It is considered that malfunction of the measurement device is due to noise. Check the noise propagation route since the countermeasure depends on it. Some c... More Details >>
- No：22100
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Others
Control circuit power supply

If the MC on the input side is shut off using the fault output of the FR-E500, the inverter's fault records are left in the faults history. More Details >>
- No：22096
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Can I set the FR-F series parameters?

The FREQROL-F500 series has been already supported by the setup software released since February 2000. More Details >>
- No：22068
- Release Date：2018/08/22 16:30
- Category： Engineering Software

671-680 of Total 1306

Inquiries

page top