- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (

1. When slight imbalance (approximately 5%) is present with the inverter power supply voltage, the inverter input curren

The test institutes assigned by the Minister of Health, Labour and Welfare (National Institute of Occupational Safety an

Noise filtering and harmonics suppression are different matters and you need to install the line noise filter (FR-BSF01)

1. Such a behavior does not usually happen. (1) The operation command (STF) is not input, contact faults are present, o

You can vary the carrier frequency within the range of 0.7 to 14.5 kHz, and it is initially set to 1 kHz that generates

Check the parameters necessary for tuning again.Check if Pr.9 (Electronic thermal O/L relay) and Pr.81 (Number of motor

1. You can set Pr.117 for "n1" (Station number) of the FR-S500 for the D700/E700/F700PJ series.2. You can set Pr.338, Pr

Pr.338 is for the communication operation command source at communication operation and specifies the command source to

Set Pr.79 (Operation mode) setting value to "0", "2", or "6", Pr.340 (Communication startup mode selection) other than t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

901-910 of Total 1306

prev 91 / 131page next

Difference between SU (up to frequency) and FU (frequency detection)

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (the frequency the inverter is require... More Details >>
- No：21436
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Current value on input side and output side

1. When slight imbalance (approximately 5%) is present with the inverter power supply voltage, the inverter input current can get imbalanced significantly. I... More Details >>
- No：21476
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-A200
Acquisition of pressure-resistant explosion-proof certification

The test institutes assigned by the Minister of Health, Labour and Welfare (National Institute of Occupational Safety and Health and Technology Institution o... More Details >>
- No：21510
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others , FREQROL-B
Noise filter

Noise filtering and harmonics suppression are different matters and you need to install the line noise filter (FR-BSF01) against noise and DCL (FR-BEL) again... More Details >>
- No：21548
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Inverter output stop

1. Such a behavior does not usually happen. 　(1) The operation command (STF) is not input, contact faults are present, or wire is broken. 　(2) The output shu... More Details >>
- No：21552
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Range of carrier frequency

You can vary the carrier frequency within the range of 0.7 to 14.5 kHz, and it is initially set to 1 kHz that generates low noise and leakage current. You ca... More Details >>
- No：21607
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
Advanced magnetic flux vector control

Check the parameters necessary for tuning again.Check if Pr.9 (Electronic thermal O/L relay) and Pr.81 (Number of motor poles) are set correctly. More Details >>
- No：21754
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
RS-485 communication

1. You can set Pr.117 for "n1" (Station number) of the FR-S500 for the D700/E700/F700PJ series.2. You can set Pr.338, Pr.339, and Pr.342 for "n8" (Operation ... More Details >>
- No：21758
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Running frequency setting

Pr.338 is for the communication operation command source at communication operation and specifies the command source to supply the start signal.Pr.339 is for... More Details >>
- No：21880
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

Set Pr.79 (Operation mode) setting value to "0", "2", or "6", Pr.340 (Communication startup mode selection) other than the setting value, Pr.542 (Station num... More Details >>
- No：21896
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P

901-910 of Total 1306

Inquiries

page top