It is 30 clicks the FR-A800/FR-F800.

It is not possible because the RS-485 terminal block is not installed. Use the FR-A800 (RS-485 communication type) when

When Pr.414 is set to "1" and Pr.388 is set to "0", the PLC function is not enabled unless both the SQ signal from commu

No, the MT-BU5 is not available Use the FR-BU2 instead.

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset t

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (again

Set the rotations per minute that is obtained while operating at the frequency set with Pr.505 (Speed setting reference)

You can use the CC-Link type programming example for the FR-E500 as a reference.In the programming example for the FR-E5

The error indicates that the parameter setting of the PLC function is not set. It is considered that the PC parameter is

When Pr.551 is set to "3" (Command right to the USB connector at the PU operation), or when the USB is connected, the op

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Inverters-FREQROL

FAQ within [ Inverters-FREQROL ]

981-990 of Total 1292

prev 99 / 130page next

FR-A800/FR-F800

It is 30 clicks the FR-A800/FR-F800. More Details >>
- No：20811
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800
FR-A800-E

It is not possible because the RS-485 terminal block is not installed. Use the FR-A800 (RS-485 communication type) when performing the RS-485 communication. More Details >>
- No：20881
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800
PLC function

When Pr.414 is set to "1" and Pr.388 is set to "0", the PLC function is not enabled unless both the SQ signal from communication and the SQ signal from the e... More Details >>
- No：21073
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800
MT-BU5

No, the MT-BU5 is not available Use the FR-BU2 instead. More Details >>
- No：21076
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , FREQROL-A800 , FREQROL-F800
CC-Link communication

After setting Pr.79 (Operation mode selection) to "2" and Pr.340 (Communication startup mode selection) to "10", reset the inverter (or power ON again) to st... More Details >>
- No：21256
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Electromagnetic contactor

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (against overcurrent or overvoltage) of the... More Details >>
- No：21725
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Display unit of operation panel

Set the rotations per minute that is obtained while operating at the frequency set with Pr.505 (Speed setting reference) to Pr.37 (Speed display).For example... More Details >>
- No：21774
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

You can use the CC-Link type programming example for the FR-E500 as a reference.In the programming example for the FR-E500, the A series programmable control... More Details >>
- No：21836
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Built-in PLC function

The error indicates that the parameter setting of the PLC function is not set. It is considered that the PC parameter is not checked when the PC parameter an... More Details >>
- No：20859
- Release Date：2018/08/22 16:24
- Category： FREQROL-A800 , FREQROL-F800
Operation mode switch of the FR-A800/F800

When Pr.551 is set to "3" (Command right to the USB connector at the PU operation), or when the USB is connected, the operation is not switched. More Details >>
- No：20861
- Release Date：2018/08/22 16:24
- Category： FREQROL-A800 , FREQROL-F800

981-990 of Total 1292

Inquiries

page top