Both settings of Pr.83 and Pr.84 are enabled immediately. However, the output voltage is not changed because the value o

The tension PI gain can be adjusted automatically by performing the tension PI gain tuning.

The RJ-45 compatible connector (LAN cable), switching hub, and others are required The auto detection of the connection

If the operation panel has not been operated for the time set in Pr.1048 Display-off waiting time, the display-off mode

The gain of the tension PI gain automatic tuning is the one of the dancer feedback speed control. The gain adjusted by s

It indicate that the actual number of connectable units differs depending on the master side specification although the

The calculation is performed by two modes. One method calculates the current winding diameter automatically by moving th

When the winding ratio is large, the control according to the winding diameter is required. The upper controller has mea

If the command is 0.01 Hz or higher, the positioning control is performed.

For the V/F control and Advanced magnetic flux vector control, the FR-A800 stops only by Pr.1103 Deceleration time at em

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A800

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-A800 ]

111-120 of Total 144

prev 12 / 15page next

Vector control

Both settings of Pr.83 and Pr.84 are enabled immediately. However, the output voltage is not changed because the value of Pr.83 has little influence on Vecto... More Details >>
- No：21022
- Release Date：2018/08/22 16:25
FR-A800-R2R

The tension PI gain can be adjusted automatically by performing the tension PI gain tuning. More Details >>
- No：20923
- Release Date：2018/08/22 16:25
FR-A800-E

The RJ-45 compatible connector (LAN cable), switching hub, and others are required The auto detection of the connection devices, externally monitoring the in... More Details >>
- No：20882
- Release Date：2018/08/22 16:24
Operation panel

If the operation panel has not been operated for the time set in Pr.1048 Display-off waiting time, the display-off mode is enabled and the "MON" LED blinks s... More Details >>
- No：21075
- Release Date：2018/08/22 16:25
FR-A800-R2R

The gain of the tension PI gain automatic tuning is the one of the dancer feedback speed control. The gain adjusted by speed control P gain compensation is t... More Details >>
- No：20925
- Release Date：2018/08/22 16:25
FR-A800-E

It indicate that the actual number of connectable units differs depending on the master side specification although the maximum number of connectable units o... More Details >>
- No：20839
- Release Date：2018/08/22 16:24
FR-A800-R2R

The calculation is performed by two modes. One method calculates the current winding diameter automatically by moving the dancer roll from lower limit positi... More Details >>
- No：20924
- Release Date：2018/08/22 16:25
FR-A800-R2R

When the winding ratio is large, the control according to the winding diameter is required. The upper controller has measured the winding diameter and create... More Details >>
- No：20974
- Release Date：2018/08/22 16:25
MM-FR-A800

If the command is 0.01 Hz or higher, the positioning control is performed. More Details >>
- No：21001
- Release Date：2018/08/22 16:25
Emergency stop of the FR-A800

For the V/F control and Advanced magnetic flux vector control, the FR-A800 stops only by Pr.1103 Deceleration time at emergency stop. Pr.815 is not affected. More Details >>
- No：20860
- Release Date：2018/08/22 16:24

111-120 of Total 144

Inquiries

page top