The value is displayed in 0.1 rpm increments under Vector control. However, the value is rounded down to the first decim

Yes, the current response is also improved at the same rate.

Number of terminals: There are the same output terminals as A700 and the following terminals (2 points) are added. Safet

Available under vector control with an encoder.* Zero speed and servo lock are available under PM sensorless vector cont

It is possible when the dancer control and tension sensor feedback speed control is used and the PID calculation is turn

When the value is written to Pr.646 (Stored winding diameter), the stored value is used. When the value is not written,

They cannot be set with the frequency. Because the command is input at the line speed, consider the line speed of the in

UVT will occur when reactor is not connected. Always connect a reactor that matches the motor capacity.

Number of terminals: Same input terminals as the A700 series, and the following two terminals are added. Safety: SI1, SI

20 ms or less is required to switch the control with the MC signal.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A800

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-A800 ]

1-10 of Total 144

prev 1 / 15page next

Frequency setting increment

The value is displayed in 0.1 rpm increments under Vector control. However, the value is rounded down to the first decimal place and displayed in 1 rpm incre... More Details >>
- No：21021
- Release Date：2018/08/22 16:25
FR-A800

Yes, the current response is also improved at the same rate. More Details >>
- No：21079
- Release Date：2018/08/22 16:25
FR-A800

Number of terminals: There are the same output terminals as A700 and the following terminals (2 points) are added. Safety: SO, SOC * The terminals SO and SOC... More Details >>
- No：21098
- Release Date：2018/08/22 16:25
FR-A800

Available under vector control with an encoder.* Zero speed and servo lock are available under PM sensorless vector control only in combination with an MM-CF... More Details >>
- No：21100
- Release Date：2018/08/22 16:25
FR-A800-R2R

It is possible when the dancer control and tension sensor feedback speed control is used and the PID calculation is turned OFF. Because the PID compensation ... More Details >>
- No：20889
- Release Date：2018/08/22 16:24
FR-A800-R2R

When the value is written to Pr.646 (Stored winding diameter), the stored value is used. When the value is not written, the minimum or maximum winding diamet... More Details >>
- No：20887
- Release Date：2018/08/22 16:24
FR-A800-R2R

They cannot be set with the frequency. Because the command is input at the line speed, consider the line speed of the initial winding diameter at 20 Hz. The ... More Details >>
- No：20888
- Release Date：2018/08/22 16:24
FR-A800

UVT will occur when reactor is not connected. Always connect a reactor that matches the motor capacity. More Details >>
- No：20978
- Release Date：2018/08/22 16:25
FR-A800

Number of terminals: Same input terminals as the A700 series, and the following two terminals are added. Safety: SI1, SI2, SIC 24 V power supply: +24 * The t... More Details >>
- No：21099
- Release Date：2018/08/22 16:25
Switching time of the FR-A800 control

20 ms or less is required to switch the control with the MC signal. More Details >>
- No：20838
- Release Date：2018/08/22 16:24

1-10 of Total 144

Inquiries

page top