You can do so by setting Pr.339 (Communication speed command source) = 1 (external).

It is recommended to install the magnetic contactor on the input side of the inverter for safety. The category 3 can be

Since the operation panel and PU connector cannot be specified for command source at the same time, they cannot be used

If "HOLD" is displayed, the key lock mode enabled. Press the "MODE" key for two seconds. Then, change the setting of Pr.

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switc

There is a priority between the setting dial and multi-speed settings.Since the multi-speed setting is given a higher pr

To set the frequency via CC-Link communication, the NET mode should be selected. The new parameter setting is applied af

Yes.The parameters used when the terminal 4 is used are C5, C6, 126, and C7.Set Pr.C5 (Terminal 4 frequency setting bias

No problem.LEDs "PU" and "EXT" indicate that Pr.79 is set to "3"."MON" indicates that the operation status is monitored.

If Pr.544 (CC-Link extended setting) is set to other than "0", you do not need to change Pr.544 (CC-Link extended settin

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

91-100 of Total 394

prev 10 / 40page next

Start command, speed command

You can do so by setting Pr.339 (Communication speed command source) = 1 (external).　　 More Details >>
- No：21881
- Release Date：2018/08/22 16:29
Safety stop function of the FR-D700/FR-E700

It is recommended to install the magnetic contactor on the input side of the inverter for safety. The category 3 can be satisfied without installing it. More Details >>
- No：20837
- Release Date：2018/08/22 16:24
Operation panel and FR-PA07

Since the operation panel and PU connector cannot be specified for command source at the same time, they cannot be used together. More Details >>
- No：21349
- Release Date：2018/08/22 16:27
Easy setting mode

If "HOLD" is displayed, the key lock mode enabled. Press the "MODE" key for two seconds. Then, change the setting of Pr.79 to "1". More Details >>
- No：21350
- Release Date：2018/08/22 16:27
FR-PA07

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switchover) is not set to "0". If it is "0... More Details >>
- No：21363
- Release Date：2018/08/22 16:27
FR-PA07

There is a priority between the setting dial and multi-speed settings.Since the multi-speed setting is given a higher priority, the setting by the setting di... More Details >>
- No：21702
- Release Date：2018/08/22 16:29
CC-Link

To set the frequency via CC-Link communication, the NET mode should be selected. The new parameter setting is applied after powering OFF and then ON the inve... More Details >>
- No：21763
- Release Date：2018/08/22 16:29
Current setting

Yes.The parameters used when the terminal 4 is used are C5, C6, 126, and C7.Set Pr.C5 (Terminal 4 frequency setting bias frequency) while feeding a current s... More Details >>
- No：21770
- Release Date：2018/08/22 16:29
Operation panel LED

No problem.LEDs "PU" and "EXT" indicate that Pr.79 is set to "3"."MON" indicates that the operation status is monitored."RUN" indicates that the inverter is ... More Details >>
- No：21776
- Release Date：2018/08/22 16:29
CC-Link

If Pr.544 (CC-Link extended setting) is set to other than "0", you do not need to change Pr.544 (CC-Link extended setting).Write the extended setting of the ... More Details >>
- No：21834
- Release Date：2018/08/22 16:29

91-100 of Total 394

Inquiries

page top