Change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (again

Leave the setting of Pr.96 as "3". It indicates that auto tuning has been completed and the motor constant has been read

Yes. However, write the setting data to the RAM of the inverter.Set RWw1 in the setting value and turn ON the frequency

This subroutine is to check the data link status and needs to be executed only once at the start of the program.

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz".

Auto tuning can be performed because the motor is one rank lower than the inverter capacity.

1. It depends on how Pr.338 (Communication operation command source) and Pr.339 (Communication speed command source) are

As the AS-OX has the "0ADJ" potentiometer for frequency meter calibration, use it to adjust the meter so that both readi

Since the external thermal prevents the motor from being overheated, install it between the output terminal of the inver

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

221-230 of Total 393

prev 23 / 40page next

Frequency setting

Change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).　　 More Details >>
- No：21792
- Release Date：2018/08/22 16:29
Electromagnetic contactor

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (against overcurrent or overvoltage) of the... More Details >>
- No：21725
- Release Date：2018/08/22 16:29
Offline auto tuning

Leave the setting of Pr.96 as "3". It indicates that auto tuning has been completed and the motor constant has been read. When it is changed unnecessarily, t... More Details >>
- No：21352
- Release Date：2018/08/22 16:27
CC-Link

Yes. However, write the setting data to the RAM of the inverter.Set RWw1 in the setting value and turn ON the frequency setting command RYD.To continuously s... More Details >>
- No：21825
- Release Date：2018/08/22 16:29
Program command

This subroutine is to check the data link status and needs to be executed only once at the start of the program. More Details >>
- No：21767
- Release Date：2018/08/22 16:29
Parameter setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz". More Details >>
- No：21720
- Release Date：2018/08/22 16:29
Offline auto tuning

Auto tuning can be performed because the motor is one rank lower than the inverter capacity. More Details >>
- No：21351
- Release Date：2018/08/22 16:27
CC-Link

1. It depends on how Pr.338 (Communication operation command source) and Pr.339 (Communication speed command source) are set.2. The external terminal reset i... More Details >>
- No：21838
- Release Date：2018/08/22 16:29
Frequency setting

As the AS-OX has the "0ADJ" potentiometer for frequency meter calibration, use it to adjust the meter so that both readings match.　　 More Details >>
- No：21795
- Release Date：2018/08/22 16:29
External installationRated current

Since the external thermal prevents the motor from being overheated, install it between the output terminal of the inverter and the motor.The rated current i... More Details >>
- No：21817
- Release Date：2018/08/22 16:29

221-230 of Total 393

Inquiries

page top