It is recommended to install the magnetic contactor on the input side of the inverter for safety. The category 3 can be

No problem. The inverter actually occupies the reserved bits and does not use them.

Set the rated frequency of the motor used to it.

Yes.The inverter requires the start signal and frequency setting signal.

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are

Change the value of Pr.18 (High speed maximum frequency).You can set any frequency within the range defined by Pr.18.

It is not stored in a parameter but memorized as the frequency setting value after acceleration by the acceleration sign

The relationship between the acceleration/deceleration reference frequency and acceleration/deceleration time does not c

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switc

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

231-240 of Total 393

prev 24 / 40page next

Safety stop function of the FR-D700/FR-E700

It is recommended to install the magnetic contactor on the input side of the inverter for safety. The category 3 can be satisfied without installing it. More Details >>
- No：20837
- Release Date：2018/08/22 16:24
CC-Link

No problem. The inverter actually occupies the reserved bits and does not use them. More Details >>
- No：21890
- Release Date：2018/08/22 16:29
Base frequency setting value

Set the rated frequency of the motor used to it.　 More Details >>
- No：21814
- Release Date：2018/08/22 16:29
Frequency setting

Yes.The inverter requires the start signal and frequency setting signal. More Details >>
- No：21793
- Release Date：2018/08/22 16:29
Minimum frequency

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with Pr.13 (Starting frequency) up to 3 H... More Details >>
- No：21777
- Release Date：2018/08/22 16:29
NET mode

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are setting the operation upon power-on.... More Details >>
- No：21759
- Release Date：2018/08/22 16:29
Frequency setting

Change the value of Pr.18 (High speed maximum frequency).You can set any frequency within the range defined by Pr.18. More Details >>
- No：21737
- Release Date：2018/08/22 16:29
Frequency setting

It is not stored in a parameter but memorized as the frequency setting value after acceleration by the acceleration signal.You can also choose whether or not... More Details >>
- No：21733
- Release Date：2018/08/22 16:29
PU operation

The relationship between the acceleration/deceleration reference frequency and acceleration/deceleration time does not change between the PU operation and ex... More Details >>
- No：21694
- Release Date：2018/08/22 16:28
FR-PA07

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switchover) is not set to "0". If it is "0... More Details >>
- No：21363
- Release Date：2018/08/22 16:27

231-240 of Total 393

Inquiries

page top