You can select deceleration stop by setting Pr.502 (Stop mode selection at communication error). (Select from coasting t

Normally, any of the PU, EXT, or NET LED turns ON.Check if the parameter unit FR-PU04/FR-PU07 or operation panel FR-PA07

Set Pr.125 (Terminal 2 frequency setting gain frequency) instead of Pr.1 (Maximum frequency).

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with

To use the terminal as voltage input, you need to:- Set Pr.267 (Terminal 4 input selection).- Set the voltage/current in

To set the frequency via CC-Link communication, the NET mode should be selected. The new parameter setting is applied af

Yes. Use a moving-iron type ammeter. However, if the carrier frequency exceeds 5 kHz, do not use that meter since an ove

1. Yes. 2. The standard set by Pr.56.

Leave the setting of Pr.96 as "3". It indicates that auto tuning has been completed and the motor constant has been read

In the initial setting, it is set to 120 Hz.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

241-250 of Total 394

prev 25 / 40page next

CC-Link

You can select deceleration stop by setting Pr.502 (Stop mode selection at communication error). (Select from coasting to stop, deceleration to stop, and con... More Details >>
- No：21892
- Release Date：2018/08/22 16:29
Frequency setting

Normally, any of the PU, EXT, or NET LED turns ON.Check if the parameter unit FR-PU04/FR-PU07 or operation panel FR-PA07 is externally connected to the PU co... More Details >>
- No：21803
- Release Date：2018/08/22 16:29
Frequency setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) instead of Pr.1 (Maximum frequency).　　 More Details >>
- No：21802
- Release Date：2018/08/22 16:29
Minimum frequency

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with Pr.13 (Starting frequency) up to 3 H... More Details >>
- No：21777
- Release Date：2018/08/22 16:29
Terminal setting

To use the terminal as voltage input, you need to:- Set Pr.267 (Terminal 4 input selection).- Set the voltage/current input switch on the inverter board.- Se... More Details >>
- No：21771
- Release Date：2018/08/22 16:29
CC-Link

To set the frequency via CC-Link communication, the NET mode should be selected. The new parameter setting is applied after powering OFF and then ON the inve... More Details >>
- No：21763
- Release Date：2018/08/22 16:29
Connecting ammeter to output side

Yes. Use a moving-iron type ammeter. However, if the carrier frequency exceeds 5 kHz, do not use that meter since an overcurrent losses produced in the inter... More Details >>
- No：21681
- Release Date：2018/08/22 16:28
A7AY

1. Yes. 　2. The standard set by Pr.56. More Details >>
- No：21669
- Release Date：2018/08/22 16:28
Offline auto tuning

Leave the setting of Pr.96 as "3". It indicates that auto tuning has been completed and the motor constant has been read. When it is changed unnecessarily, t... More Details >>
- No：21352
- Release Date：2018/08/22 16:27
Output frequency

In the initial setting, it is set to 120 Hz. More Details >>
- No：21345
- Release Date：2018/08/22 16:27

241-250 of Total 394

Inquiries

page top