Since Advanced magnetic flux vector control is chosen, the inverter calculates how much the motor rotation slips from th

Set Pr.270 (Stop-on-contact control) to "1".Set Pr.184 (RES terminal function selection) to "3" to choose the RT signal

Use Pr.C24 (Frequency setting voltage gain frequency built-in potentiometer).

Basically it is not possible due to the operation command source.However, if Pr.77 (Parameter write selection) is set to

Yes, you can set all of the three relay contacts to fault contacts.Set Pr.320 (RA1 output selection), 321 (RA2 output se

The ferrule terminal or single wire can be used for the control circuit wiring.

On the Mitsubishi Electric FA Global Website, choose "Inverter FREQROL", "Manual", and "FREQROL-E700", and change the la

Only the operation command source is switched to the FR-A07 and the inverter operation panel does not turn off. (Setting

The following is the amount of heat generated for each capacity:0.4K: 40W 0.75K: 55W 1.5K: 90W 2.2K: 100W3.7K: 180W

Check if Pr.13 (Starting frequency) is set to higher than 10 Hz.Also check if a signal is input through the terminal MRS

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

21-30 of Total 393

prev 3 / 40page next

Frequency setting

Since Advanced magnetic flux vector control is chosen, the inverter calculates how much the motor rotation slips from the flowing current and adds the slip a... More Details >>
- No：21684
- Release Date：2018/08/22 16:28
Stop-on-contact control

Set Pr.270 (Stop-on-contact control) to "1".Set Pr.184 (RES terminal function selection) to "3" to choose the RT signal function.When the terminals RL and RT... More Details >>
- No：21691
- Release Date：2018/08/22 16:28
FR-E700

Use Pr.C24 (Frequency setting voltage gain frequency built-in potentiometer). More Details >>
- No：21847
- Release Date：2018/08/22 16:29
FR-PA07

Basically it is not possible due to the operation command source.However, if Pr.77 (Parameter write selection) is set to "2", you can use both the FR-PA07 an... More Details >>
- No：21698
- Release Date：2018/08/22 16:28
FR-A7AR E kit (Relay output function)

Yes, you can set all of the three relay contacts to fault contacts.Set Pr.320 (RA1 output selection), 321 (RA2 output selection), and 322 (RA3 output selecti... More Details >>
- No：21712
- Release Date：2018/08/22 16:29
Wiring and terminal

The ferrule terminal or single wire can be used for the control circuit wiring. More Details >>
- No：21275
- Release Date：2018/08/22 16:26
English manual

On the Mitsubishi Electric FA Global Website, choose "Inverter FREQROL", "Manual", and "FREQROL-E700", and change the language to "English". More Details >>
- No：21666
- Release Date：2018/08/22 16:28
FR-PA07

Only the operation command source is switched to the FR-A07 and the inverter operation panel does not turn off. (Setting from the inverter operation panel be... More Details >>
- No：21699
- Release Date：2018/08/22 16:28
FR-E740

The following is the amount of heat generated for each capacity:0.4K: 40W　　0.75K: 55W　　1.5K: 90W　　2.2K: 100W3.7K: 180W　　5.5K: 240W　　7.5K: 300W　　11K: 400W15K:... More Details >>
- No：21705
- Release Date：2018/08/22 16:29
Parameter setting

Check if Pr.13 (Starting frequency) is set to higher than 10 Hz.Also check if a signal is input through the terminal MRS. More Details >>
- No：21722
- Release Date：2018/08/22 16:29

21-30 of Total 393

Inquiries

page top