The frequency can be set to 65 Hz with the initial setting.Check if Pr.1 (Maximum frequency) is set to 60 Hz.

Frequency meter: YM206NRI 1 mA Calibration resistor: RV24YN 10 k?.

The mounting screw is not supplied. The mounting screw is supplied with the operation panel. Open the screw hole accordi

Yes, you can set Pr.20 to 20 Hz.

You can use the setting dial to set the frequency during operation even if Pr.77 is not set to "2".Setting Pr.77 to "2"

You can change the terminal 4 to voltage input. (The terminal 4 is set to the current input terminal at the initial sett

It is Pr.125 (Terminal 2 frequency setting gain frequency). Adjust the slope with C4 (903) (Terminal 2 frequency setting

Check if the input side voltage is equally applied to all three phases. The S phase voltage may be low because the input

For the Instruction Manual "Applied", fill in the request sheet which is included in the last part of the Instruction Ma

For the set frequency 60 Hz, ±6 Hz is applied and thus the up to frequency signal is output between 54 Hz and 66 Hz. Dur

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

291-300 of Total 394

prev 30 / 40page next

Frequency setting

The frequency can be set to 65 Hz with the initial setting.Check if Pr.1 (Maximum frequency) is set to 60 Hz. More Details >>
- No：21858
- Release Date：2018/08/22 16:29
Frequency meter and calibration resistor

Frequency meter: YM206NRI 1 mA Calibration resistor: RV24YN 10 k?. More Details >>
- No：21357
- Release Date：2018/08/22 16:27
FR-PA07

The mounting screw is not supplied. The mounting screw is supplied with the operation panel. Open the screw hole according to the dimension. (The M3 screw is... More Details >>
- No：21361
- Release Date：2018/08/22 16:27
Frequency setting

Yes, you can set Pr.20 to 20 Hz. More Details >>
- No：21683
- Release Date：2018/08/22 16:28
Frequency setting

You can use the setting dial to set the frequency during operation even if Pr.77 is not set to "2".Setting Pr.77 to "2" allows for changing the parameter set... More Details >>
- No：21786
- Release Date：2018/08/22 16:29
Frequency setting

You can change the terminal 4 to voltage input. (The terminal 4 is set to the current input terminal at the initial setting.)To change the terminal 4 to volt... More Details >>
- No：21787
- Release Date：2018/08/22 16:29
Replacement

It is Pr.125 (Terminal 2 frequency setting gain frequency). Adjust the slope with C4 (903) (Terminal 2 frequency setting gain) as necessary. More Details >>
- No：21247
- Release Date：2018/08/22 16:26
Input phase loss

Check if the input side voltage is equally applied to all three phases. The S phase voltage may be low because the input current flows when the voltage of th... More Details >>
- No：21340
- Release Date：2018/08/22 16:27
Instruction manual

For the Instruction Manual "Applied", fill in the request sheet which is included in the last part of the Instruction Manual "Basic", and fax it to the speci... More Details >>
- No：21341
- Release Date：2018/08/22 16:27
Frequency setting

For the set frequency 60 Hz, ±6 Hz is applied and thus the up to frequency signal is output between 54 Hz and 66 Hz. During acceleration/deceleration to the ... More Details >>
- No：21348
- Release Date：2018/08/22 16:27

291-300 of Total 394

Inquiries

page top