You can change the terminal 4 to voltage input. (The terminal 4 is set to the current input terminal at the initial sett

Check the setting of Pr.79 (Operation mode).If the setting value is "2", frequency commands from an external terminal is

Check if the input side voltage is equally applied to all three phases. The S phase voltage may be low because the input

Normally, Pr.80 and Pr.81 are the parameters that can be changed when the operation is stopped in the PU operation mode.

Since Pr.3 (Base frequency) is a parameter to set the rated motor frequency, setting it to 80 Hz does not increase the f

When FR Configurator (FR-SW3-SETUP-WJ) is saved as a file from the menu, the extension is "me3". The size of this fie wi

The FR-E700 is not supported by FR-SW2-SETUP-WJ. The FR-E700 series are supported by FR-SW3-SETUP-WJ. This software can

You can use the setting dial to set the frequency during operation even if Pr.77 is not set to "2".Setting Pr.77 to "2"

Set Pr.79 (Operation mode) to "1" (PU operation mode) and change Pr.161 (Frequency setting/key lock operation selection)

Set Pr.79 to "2" (external operation mode).

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

31-40 of Total 393

prev 4 / 40page next

Frequency setting

You can change the terminal 4 to voltage input. (The terminal 4 is set to the current input terminal at the initial setting.)To change the terminal 4 to volt... More Details >>
- No：21787
- Release Date：2018/08/22 16:29
Frequency setting

Check the setting of Pr.79 (Operation mode).If the setting value is "2", frequency commands from an external terminal is effective and the frequency setting ... More Details >>
- No：21797
- Release Date：2018/08/22 16:29
Input phase loss

Check if the input side voltage is equally applied to all three phases. The S phase voltage may be low because the input current flows when the voltage of th... More Details >>
- No：21340
- Release Date：2018/08/22 16:27
Parameter display setting

Normally, Pr.80 and Pr.81 are the parameters that can be changed when the operation is stopped in the PU operation mode. The "Er4" is a mode designation erro... More Details >>
- No：21335
- Release Date：2018/08/22 16:27
Frequency setting

Since Pr.3 (Base frequency) is a parameter to set the rated motor frequency, setting it to 80 Hz does not increase the frequency.Set this parameter to the ra... More Details >>
- No：21788
- Release Date：2018/08/22 16:29
Saving parameter with FR-Configurator

When FR Configurator (FR-SW3-SETUP-WJ) is saved as a file from the menu, the extension is "me3". The size of this fie will be large since device settings and... More Details >>
- No：21311
- Release Date：2018/08/22 16:26
Supported model for FR-Configurator

The FR-E700 is not supported by FR-SW2-SETUP-WJ. The FR-E700 series are supported by FR-SW3-SETUP-WJ. This software can be downloaded from the Mitsubishi Ele... More Details >>
- No：21314
- Release Date：2018/08/22 16:26
Frequency setting

You can use the setting dial to set the frequency during operation even if Pr.77 is not set to "2".Setting Pr.77 to "2" allows for changing the parameter set... More Details >>
- No：21786
- Release Date：2018/08/22 16:29
PU operation

Set Pr.79 (Operation mode) to "1" (PU operation mode) and change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).　　 More Details >>
- No：21863
- Release Date：2018/08/22 16:29
Operation mode setting value

Set Pr.79 to "2" (external operation mode).　　　 More Details >>
- No：21818
- Release Date：2018/08/22 16:29

31-40 of Total 393

Inquiries

page top