Set Pr.340 (Communication startup mode selection) to "10".The operation mode can be switched between PU and NET by assig

Set the rated motor current to Pr.9. It is the heat protection setting for the motor, and thus the inverter does not shu

To use Advanced magnetic flux vector control, basically set Pr.9, Pr.80, Pr.81, Pr.71, and Pr.800.Auto tuning is necessa

The FR-E700, D700, F700PJ may activate input phase loss protection "E.ILF" if the phase-to-phase voltage of the power su

Checking terminals used:Are the terminals MRS and RES open?Are the terminals STR and SD short-circuited correctly?Is the

Advanced magnetic flux vector control provides a larger torque at low-speed. 3.7K or lower: 0.5 Hz/200%5.5K to 15K: 0.5

When the FR-PA02 is connected to the inverter with a cable, the FR-PA02 becomes effective.The operation panel of the inv

You cannot use the setting dial while the terminals JOG and SD are turned ON.When performing JOG operation using externa

You also need to set Pr.57 (Restart coasting time).The function does not work just by setting Pr.162 unless setting this

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch whil

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-E700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-E700 ]

61-70 of Total 394

prev 7 / 40page next

Switching between PU and NET operation modes

Set Pr.340 (Communication startup mode selection) to "10".The operation mode can be switched between PU and NET by assigning X65 (PU-NET operation switching)... More Details >>
- No：21878
- Release Date：2018/08/22 16:29
Fault output terminal A, B, and C

Set the rated motor current to Pr.9. It is the heat protection setting for the motor, and thus the inverter does not shutoff immediately at the specified cur... More Details >>
- No：21324
- Release Date：2018/08/22 16:27
Advanced magnetic flux vector control

To use Advanced magnetic flux vector control, basically set Pr.9, Pr.80, Pr.81, Pr.71, and Pr.800.Auto tuning is necessary in some cases. Set Pr.83, Pr.84, a... More Details >>
- No：21755
- Release Date：2018/08/22 16:29
Input phase loss

The FR-E700, D700, F700PJ may activate input phase loss protection "E.ILF" if the phase-to-phase voltage of the power supply has become largely unbalanced. More Details >>
- No：21339
- Release Date：2018/08/22 16:27
External 0 to 10 VDC input

Checking terminals used:Are the terminals MRS and RES open?Are the terminals STR and SD short-circuited correctly?Is the voltage/current switch of the termin... More Details >>
- No：21916
- Release Date：2018/08/22 16:30
Advanced magnetic flux vector control and General-purpose magnetic flux vector control

Advanced magnetic flux vector control provides a larger torque at low-speed. 3.7K or lower: 0.5 Hz/200%5.5K to 15K: 0.5 Hz/150% More Details >>
- No：21297
- Release Date：2018/08/22 16:26
Setting dial and FR-PA02 built-in potentiometer

When the FR-PA02 is connected to the inverter with a cable, the FR-PA02 becomes effective.The operation panel of the inverter can also be used to set some pa... More Details >>
- No：21861
- Release Date：2018/08/22 16:29
RUN blinks

You cannot use the setting dial while the terminals JOG and SD are turned ON.When performing JOG operation using external signals, set Pr.79 (Operation mode)... More Details >>
- No：21823
- Release Date：2018/08/22 16:29
Automatic restart after instantaneous power failure setting

You also need to set Pr.57 (Restart coasting time).The function does not work just by setting Pr.162 unless setting this parameter.(For A700, F700, and F700P... More Details >>
- No：21731
- Release Date：2018/08/22 16:29
Switching between external operation and NET operation

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch while Pr.79 (Operation mode) is set to "6... More Details >>
- No：21688
- Release Date：2018/08/22 16:28

61-70 of Total 394

Inquiries

page top