The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform.

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switc

No, we have no cable 50 cm long. The optional cables 1 m, 3 m, and 5 m long are available. (1 m: FR-CB201, 3 m: FR-CB203

Operations cannot be enabled separately. You only can disable or enable all the operations.

You can connect a 1 mA full scale ammeter with internal resistance 300 Ω or lower.

Yes, you can use the setup software (FR-SW3-SETUP-WJ) to set it.

Set Pr.37 (Speed display) to the speed obtained when operating the machine at the frequency set with Pr.505 (Speed setti

Set Pr.55 (Frequency monitor reference) to "100 Hz".If the indication of the installed frequency meter does not match th

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note t

The calibration parameter C6 (Terminal 4 frequency setting bias) is initially set to "20%". Therefore, voltage input to

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-D700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-D700 ]

91-100 of Total 261

prev 10 / 27page next

Terminal indicator lamp

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform. Check if the lamp to be connected ca... More Details >>
- No：21323
- Release Date：2018/08/22 16:27
FR-PA07

Specific settings are not required, however, when replacing the FR-E500, check that Pr.146 (Built-in potentiometer switchover) is not set to "0". If it is "0... More Details >>
- No：21363
- Release Date：2018/08/22 16:27
FR-PA07

No, we have no cable 50 cm long. The optional cables 1 m, 3 m, and 5 m long are available. (1 m: FR-CB201, 3 m: FR-CB203, 5 m: FR-CB205) More Details >>
- No：21365
- Release Date：2018/08/22 16:27
FR-PA07

Operations cannot be enabled separately. You only can disable or enable all the operations. More Details >>
- No：21366
- Release Date：2018/08/22 16:27
Terminal FM

You can connect a 1 mA full scale ammeter with internal resistance 300 Ω or lower. More Details >>
- No：21680
- Release Date：2018/08/22 16:28
FR-Configurator

Yes, you can use the setup software (FR-SW3-SETUP-WJ) to set it.　　 More Details >>
- No：21711
- Release Date：2018/08/22 16:29
Monitor indicator

Set Pr.37 (Speed display) to the speed obtained when operating the machine at the frequency set with Pr.505 (Speed setting reference). (For FR-F700/E700/D700... More Details >>
- No：21716
- Release Date：2018/08/22 16:29
Parameter setting

Set Pr.55 (Frequency monitor reference) to "100 Hz".If the indication of the installed frequency meter does not match the running frequency, use the calibrat... More Details >>
- No：21768
- Release Date：2018/08/22 16:29
Frequency setting

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note that this terminal AU is not prepared ... More Details >>
- No：21799
- Release Date：2018/08/22 16:29
Frequency setting

The calibration parameter C6 (Terminal 4 frequency setting bias) is initially set to "20%". Therefore, voltage input to the terminal 4 does not become effect... More Details >>
- No：21806
- Release Date：2018/08/22 16:29

91-100 of Total 261

Inquiries

page top