Check that the correct rated motor current is set in Pr.9 (Electronic thermal O/L relay). No parameter is available for

Set Pr.338 (Communication command source) to "0" to give a start command from "NET". Set Pr.339 (Speed command source) t

When the torque is supposed as 100% at 60 Hz, the torque becomes 75 % at 80 Hz. (Under V/F control, the torque decreases

To set the motor to coasting state, the following methods are available: 1. Set Pr.250 (Stop selection) to "0" and turn

Check that the wiring of the terminal 4 and 5 are not reversed.

The FR-DU04 can be used in the 700 series inverters, however, some restrictions apply and parameter copy is disabled.

Normally, the auto tuning condition depends on the combination of the inverter and motor (including wiring to the motor)

Check that Pr.3 (Base frequency) is set to "200 Hz". Adjust Pr.0 (Torque boost) as necessary.

The length within 30 m is recommended. When the wiring length is long, signals may not be received accurately due to the

The Radio Act applies to the products used for the purpose of the radio waves. Inverters are used for motor drive and th

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-D700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-D700 ]

211-220 of Total 261

prev 22 / 27page next

Electronic thermal O/L relay

Check that the correct rated motor current is set in Pr.9 (Electronic thermal O/L relay). No parameter is available for setting the operation time of the ele... More Details >>
- No：21291
- Release Date：2018/08/22 16:26
Start command

Set Pr.338 (Communication command source) to "0" to give a start command from "NET". Set Pr.339 (Speed command source) to "1" to make a frequency setting fro... More Details >>
- No：21285
- Release Date：2018/08/22 16:26
Frequency

When the torque is supposed as 100% at 60 Hz, the torque becomes 75 % at 80 Hz. (Under V/F control, the torque decreases when the frequency exceeds 60 Hz bec... More Details >>
- No：21284
- Release Date：2018/08/22 16:26
Motor coasting

To set the motor to coasting state, the following methods are available: 1. Set Pr.250 (Stop selection) to "0" and turn OFF the start command. 2. Short the t... More Details >>
- No：21271
- Release Date：2018/08/22 16:26
Frequency setting signal

Check that the wiring of the terminal 4 and 5 are not reversed. More Details >>
- No：21266
- Release Date：2018/08/22 16:26
Operation panel (DU04)

The FR-DU04 can be used in the 700 series inverters, however, some restrictions apply and parameter copy is disabled. More Details >>
- No：21261
- Release Date：2018/08/22 16:26
Auto tuning

Normally, the auto tuning condition depends on the combination of the inverter and motor (including wiring to the motor), perform auto tuning each time. The ... More Details >>
- No：21293
- Release Date：2018/08/22 16:26
Rated frequency setting

Check that Pr.3 (Base frequency) is set to "200 Hz". Adjust Pr.0 (Torque boost) as necessary. More Details >>
- No：21280
- Release Date：2018/08/22 16:26
Output signal

The length within 30 m is recommended. When the wiring length is long, signals may not be received accurately due to the increased inductance. More Details >>
- No：20995
- Release Date：2018/08/22 16:25
Radio Act

The Radio Act applies to the products used for the purpose of the radio waves. Inverters are used for motor drive and thus out of the scope. More Details >>
- No：20994
- Release Date：2018/08/22 16:25

211-220 of Total 261

Inquiries

page top