You can monitor the fault output in both NET operation and external operation.

Yes, you can set Pr.20 to 20 Hz.

Yes, it does. When the inverter is coasting in the reverse direction, it starts in the reverse direction and switches to

Checking terminals used:Are the terminals MRS and RES open?Are the terminals STR and SD short-circuited correctly?Is the

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch whil

Since Pr.125 (Terminal 2 frequency setting gain frequency) is initially set to 60 Hz, change it to 85 Hz.

Not possible.Instead of FR-DU07, use FR-PA07 (or FR-PU07) as an operation panel for FR-E700.

Auto tuning can be performed because the motor is one rank lower than the inverter capacity.

Set the rated motor current to Pr.9. It is the heat protection setting for the motor, and thus the inverter does not shu

For the models other than FR-A700/F700, use FR-Configurator (FR-SW3-SETUP-WJ). They are not supported by FR-Configurator

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-D700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-D700 ]

21-30 of Total 260

prev 3 / 26page next

Switching between external operation and NET operation

You can monitor the fault output in both NET operation and external operation. More Details >>
- No：21686
- Release Date：2018/08/22 16:28
Frequency setting

Yes, you can set Pr.20 to 20 Hz. More Details >>
- No：21683
- Release Date：2018/08/22 16:28
Reverse rotation prevention selection

Yes, it does. When the inverter is coasting in the reverse direction, it starts in the reverse direction and switches to the forward rotation after a deceler... More Details >>
- No：21125
- Release Date：2018/08/22 16:26
External 0 to 10 VDC input

Checking terminals used:Are the terminals MRS and RES open?Are the terminals STR and SD short-circuited correctly?Is the voltage/current switch of the termin... More Details >>
- No：21916
- Release Date：2018/08/22 16:30
Switching between external operation and NET operation

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch while Pr.79 (Operation mode) is set to "6... More Details >>
- No：21688
- Release Date：2018/08/22 16:28
Frequency setting

Since Pr.125 (Terminal 2 frequency setting gain frequency) is initially set to 60 Hz, change it to 85 Hz. More Details >>
- No：21907
- Release Date：2018/08/22 16:30
FR-DU07

Not possible.Instead of FR-DU07, use FR-PA07　(or FR-PU07) as an operation panel for FR-E700. More Details >>
- No：21708
- Release Date：2018/08/22 16:29
Offline auto tuning

Auto tuning can be performed because the motor is one rank lower than the inverter capacity. More Details >>
- No：21351
- Release Date：2018/08/22 16:27
Fault output terminal A, B, and C

Set the rated motor current to Pr.9. It is the heat protection setting for the motor, and thus the inverter does not shutoff immediately at the specified cur... More Details >>
- No：21324
- Release Date：2018/08/22 16:27
Supported model for FR-Configurator

For the models other than FR-A700/F700, use FR-Configurator (FR-SW3-SETUP-WJ). They are not supported by FR-Configurator (FR-SW2-SETUP-WJ). When you have the... More Details >>
- No：21313
- Release Date：2018/08/22 16:26

21-30 of Total 260

Inquiries

page top