It is recommended to install the magnetic contactor on the input side of the inverter for safety. The category 3 can be

Normally, the auto tuning condition depends on the combination of the inverter and motor (including wiring to the motor)

Operations cannot be enabled separately. You only can disable or enable all the operations.

Set Pr.40 (RUN key rotation direction selection) to "1" (Reverse).

Change Pr.146 (Built-in potentiometer switching) to "0" (built-in frequency setting potentiometer).

The forward rotation and reverse rotation are enabled by pressing the FWD/REV key on the operation panel.

1. Press the PU/EXT key on the operation panel FR-PA07 to choose the PU operation mode. Set Pr.161 (Frequency setting/ke

The station numbers that can be set differ depending on the version of FR-Configurator (FR-SW3-SETUP-WJ) setup software.

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform.

Since the percent value read by the calibration parameter C7 indicates that the voltage of 10 V is internally detected a

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-D700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-D700 ]

31-40 of Total 260

prev 4 / 26page next

Safety stop function of the FR-D700/FR-E700

It is recommended to install the magnetic contactor on the input side of the inverter for safety. The category 3 can be satisfied without installing it. More Details >>
- No：20837
- Release Date：2018/08/22 16:24
Auto tuning

Normally, the auto tuning condition depends on the combination of the inverter and motor (including wiring to the motor), perform auto tuning each time. The ... More Details >>
- No：21293
- Release Date：2018/08/22 16:26
FR-PA07

Operations cannot be enabled separately. You only can disable or enable all the operations. More Details >>
- No：21366
- Release Date：2018/08/22 16:27
PU operation

Set Pr.40 (RUN key rotation direction selection) to "1" (Reverse). More Details >>
- No：21693
- Release Date：2018/08/22 16:28
FR-PA02 built-in potentiometer

Change Pr.146 (Built-in potentiometer switching) to "0" (built-in frequency setting potentiometer). More Details >>
- No：21862
- Release Date：2018/08/22 16:29
FR-PA07

The forward rotation and reverse rotation are enabled by pressing the FWD/REV key on the operation panel. More Details >>
- No：21364
- Release Date：2018/08/22 16:27
FR-PA07

1. Press the PU/EXT key on the operation panel FR-PA07 to choose the PU operation mode. Set Pr.161 (Frequency setting/key lock operation selection) to "1" an... More Details >>
- No：21761
- Release Date：2018/08/22 16:29
Number of stations that can be set in FR Configurator

The station numbers that can be set differ depending on the version of FR-Configurator (FR-SW3-SETUP-WJ) setup software. For Ver.2.00 or later, station numbe... More Details >>
- No：21305
- Release Date：2018/08/22 16:26
Terminal indicator lamp

The inverter outputs the peak voltage 300 to 400 VDC of the bus voltage not in a pure sine wave but a in a PWM waveform. Check if the lamp to be connected ca... More Details >>
- No：21323
- Release Date：2018/08/22 16:27
Frequency setting

Since the percent value read by the calibration parameter C7 indicates that the voltage of 10 V is internally detected as 101.0%, use 101.0% as is.If you cha... More Details >>
- No：21740
- Release Date：2018/08/22 16:29

31-40 of Total 260

Inquiries

page top