It is Pr.125 (Terminal 2 frequency setting gain frequency). Adjust the slope with C4 (903) (Terminal 2 frequency setting

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542

Check the parameters listed below necessary for tuning again.Pr.9, Pr.71, Pr.80, Pr.81, Pr.83, Pr.84, and Pr.96

Please use the inverter optional FR-A7AY.It supports voltage output (0 to 10 VDC) and current output (0 to 20 mA DC).For

You cannot monitor the running frequency and conveyor speed (machine speed) simultaneously.The inverter does not have a

The start commands cannot be input from both sources simultaneously because the operation command source is specified.Yo

You can check the fault records with Pr.544 (CC-Link extended setting) set to "12" for double setting.Set H74 for the in

Slow blinking of the RUN LED indicates reverse operation.Fast blinking indicates that while the start command is input,

The inverter restart operation is disabled at turn-OFF of the CS signal while a value other than "9999" (with restart) i

Set C5 (Pr.904) (Terminal 4 frequency setting bias frequency) to 0 Hz and Pr.126 (Terminal 4 frequency setting gain freq

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-A700 ]

91-100 of Total 351

prev 10 / 36page next

Replacement

It is Pr.125 (Terminal 2 frequency setting gain frequency). Adjust the slope with C4 (903) (Terminal 2 frequency setting gain) as necessary. More Details >>
- No：21247
- Release Date：2018/08/22 16:26
Replacement

The station number and baud rate were set using the dial for the FR-A5NC, but parameter is used for the FR-A7NC. Pr.542 (Communication station number (CC-Lin... More Details >>
- No：21248
- Release Date：2018/08/22 16:26
Tuning

Check the parameters listed below necessary for tuning again.Pr.9, Pr.71, Pr.80, Pr.81, Pr.83, Pr.84, and Pr.96 More Details >>
- No：21726
- Release Date：2018/08/22 16:29
Programmable controller

Please use the inverter optional FR-A7AY.It supports voltage output (0 to 10 VDC) and current output (0 to 20 mA DC).For the voltage output (0 to 10 VDC), th... More Details >>
- No：21812
- Release Date：2018/08/22 16:29
CC-Link

You cannot monitor the running frequency and conveyor speed (machine speed) simultaneously.The inverter does not have a function to output them simultaneously. More Details >>
- No：21827
- Release Date：2018/08/22 16:29
CC-Link

The start commands cannot be input from both sources simultaneously because the operation command source is specified.You can switch the command source as ne... More Details >>
- No：21828
- Release Date：2018/08/22 16:29
CC-Link

You can check the fault records with Pr.544 (CC-Link extended setting) set to "12" for double setting.Set H74 for the instruction code and turn ON RYF. More Details >>
- No：21829
- Release Date：2018/08/22 16:29
CC-Link

Slow blinking of the RUN LED indicates reverse operation.Fast blinking indicates that while the start command is input, the running frequency command is not ... More Details >>
- No：21833
- Release Date：2018/08/22 16:29
Automatic restart after instantaneous power failure

The inverter restart operation is disabled at turn-OFF of the CS signal while a value other than "9999" (with restart) is set in Pr.57. The terminals CS and ... More Details >>
- No：21255
- Release Date：2018/08/22 16:26
Frequency setting signal

Set C5 (Pr.904) (Terminal 4 frequency setting bias frequency) to 0 Hz and Pr.126 (Terminal 4 frequency setting gain frequency) to 50 Hz. More Details >>
- No：21268
- Release Date：2018/08/22 16:26

91-100 of Total 351

Inquiries

page top