Considering voltage drop of the internal power supply and influence by noise, the wiring length should be 30 m or less.

Set Pr.52 (PU/DU main display data selection) to "5".Set the monitor as the third monitor, frequency -> current ->

You can monitor the fault output in both NET operation and external operation.

Assign X16 signal, and set Pr.79 to "0", to switch the operation mode with turning ON/OFF X16 signal.

To enable the frequency setting with the setting dial and multi-speed setting, set Pr.79 to "3". Note that multi-speed s

Yes.The parameters used when the terminal 4 is used are C5, C6, 126, and C7.Set Pr.C5 (Terminal 4 frequency setting bias

The resistors cannot be used in combination other than described. Operations of brake units and inverters are not verifi

Set Pr.340 (Communication startup mode selection) to "10".The operation mode can be switched between PU and NET by assig

Slow blinking of the RUN LED indicates reverse operation.Fast blinking indicates that while the start command is input,

It is the standardized Mini-B connector.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-A700 ]

91-100 of Total 351

prev 10 / 36page next

Frequency manual controller FR-AX

Considering voltage drop of the internal power supply and influence by noise, the wiring length should be 30 m or less. More Details >>
- No：21809
- Release Date：2018/08/22 16:29
Frequency, monitor setting

Set Pr.52 (PU/DU main display data selection) to "5".Set the monitor as the third monitor, frequency -> current -> setting frequency. More Details >>
- No：21745
- Release Date：2018/08/22 16:29
Switching between external operation and NET operation

You can monitor the fault output in both NET operation and external operation. More Details >>
- No：21686
- Release Date：2018/08/22 16:28
Switching between External operation mode and PU operation mode

Assign X16 signal, and set Pr.79 to "0", to switch the operation mode with turning ON/OFF X16 signal. More Details >>
- No：21288
- Release Date：2018/08/22 16:26
Operation mode setting

To enable the frequency setting with the setting dial and multi-speed setting, set Pr.79 to "3". Note that multi-speed setting is prioritized over setting us... More Details >>
- No：21852
- Release Date：2018/08/22 16:29
Current setting

Yes.The parameters used when the terminal 4 is used are C5, C6, 126, and C7.Set Pr.C5 (Terminal 4 frequency setting bias frequency) while feeding a current s... More Details >>
- No：21770
- Release Date：2018/08/22 16:29
Brake unit

The resistors cannot be used in combination other than described. Operations of brake units and inverters are not verified. When resistors are used in uncert... More Details >>
- No：21328
- Release Date：2018/08/22 16:27
Switching between PU and NET operation modes

Set Pr.340 (Communication startup mode selection) to "10".The operation mode can be switched between PU and NET by assigning X65 (PU-NET operation switching)... More Details >>
- No：21878
- Release Date：2018/08/22 16:29
CC-Link

Slow blinking of the RUN LED indicates reverse operation.Fast blinking indicates that while the start command is input, the running frequency command is not ... More Details >>
- No：21833
- Release Date：2018/08/22 16:29
Connection cable of FR-Configurator

It is the standardized Mini-B connector. More Details >>
- No：21312
- Release Date：2018/08/22 16:26

91-100 of Total 351

Inquiries

page top