It seems that calibration for 20 mA current signal input is not correct.Use the calibration parameters "126" and "C7" to

You can use the setting dial to set the frequency during operation even if Pr.77 is not set to "2".Setting Pr.77 to "2"

Set Pr.13 (Starting frequency) or Pr.2 (Lower limit) to "5 Hz".Also set Pr.10 (DC injection brake operation frequency) t

Change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).

When the potentiometer is disconnected and frequency commands cease, the input potential becomes around 0 V.Therefore, t

As the AS-OX has the "0ADJ" potentiometer for frequency meter calibration, use it to adjust the meter so that both readi

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note t

When running the inverter in Advanced magnetic flux vector control, the frequency setting value is increased by the amou

In this case, the JOG operation is prioritized.When the terminals JOG and SD are short-circuited and turned ON, the freq

Pr.1 (Maximum frequency) or Pr.18 (High speed maximum frequency).

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products > Inverters-FREQROL > FREQROL-A700

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

FAQ within [ FREQROL-A700 ]

141-150 of Total 352

prev 15 / 36page next

Frequency

It seems that calibration for 20 mA current signal input is not correct.Use the calibration parameters "126" and "C7" to calibrate the inverter.Perform calib... More Details >>
- No：21785
- Release Date：2018/08/22 16:29
Frequency setting

You can use the setting dial to set the frequency during operation even if Pr.77 is not set to "2".Setting Pr.77 to "2" allows for changing the parameter set... More Details >>
- No：21786
- Release Date：2018/08/22 16:29
Frequency setting

Set Pr.13 (Starting frequency) or Pr.2 (Lower limit) to "5 Hz".Also set Pr.10 (DC injection brake operation frequency) to "5 Hz".The inverter does not operat... More Details >>
- No：21790
- Release Date：2018/08/22 16:29
Frequency setting

Change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).　　 More Details >>
- No：21792
- Release Date：2018/08/22 16:29
Frequency setting

When the potentiometer is disconnected and frequency commands cease, the input potential becomes around 0 V.Therefore, the frequency command becomes analog-c... More Details >>
- No：21794
- Release Date：2018/08/22 16:29
Frequency setting

As the AS-OX has the "0ADJ" potentiometer for frequency meter calibration, use it to adjust the meter so that both readings match.　　 More Details >>
- No：21795
- Release Date：2018/08/22 16:29
Frequency setting

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note that this terminal AU is not prepared ... More Details >>
- No：21799
- Release Date：2018/08/22 16:29
Frequency setting

When running the inverter in Advanced magnetic flux vector control, the frequency setting value is increased by the amount of the motor's slippage, resulting... More Details >>
- No：21801
- Release Date：2018/08/22 16:29
Frequency setting

In this case, the JOG operation is prioritized.When the terminals JOG and SD are short-circuited and turned ON, the frequency setting by the external potenti... More Details >>
- No：21804
- Release Date：2018/08/22 16:29
Frequency setting

Pr.1 (Maximum frequency) or Pr.18 (High speed maximum frequency).　　 More Details >>
- No：21805
- Release Date：2018/08/22 16:29

141-150 of Total 352

Inquiries

page top